User manual NILFISK WST 100

[. . . ] 3 Setting up - connection to the power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Vacuuming liquids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Maintenance and repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Comply with the safety indications and prescriptions in this instruction manual. WARNING!The vacuum cleaner must not be used or stored outdoors, or in damp places. If foam or liquid spills from the vacuum cleaner, switch it off iinediately and check for the cause. 09/2009 2 WSS100 - WST100 DV Vacuum cleaner description Labels Figure 1 1 2 3 4 5 6 7 8 9 10 11 Identification plate: Code of the model, technical specifications, serial number, CE marking, year of manufacture Liquid container Controls (switches) Inlet Vacuum motors Liquid container closing band Diverter valve control (WST 100 only) Liquid level indicator tube Drain valve Safety filters Float for stopping liquids (located under chip basket) Packing and unpacking Dispose of the packing materials in compliance with the laws in force. Figure 2 Model WSS 100 WST 100 A (in) 28 28 B (in) 34 47 C (in) 59 59 Lbs 143 165 Vacuuming of liquids and shavings When the machine vacuums shavings and liquids produced during the machining process, the solid shavings are captured in the chip basket. Liquids flow into the container underneath (2). Before turning on the vacuum cleaner, fit the vacuum hose into the inlet (4) and then fit the required tool to the end of the hose. The float (11) stops the vacuuming operation (the vacuuming units remain activated) when the liquid container (2) is full; it is then necessary to turn off the vacuum cleaner and to empty the liquid container (2). 3 09/2009 WSS100 - WST100 DV Setting up - connection to the power supply WARNING!· · Make sure that the vacuum cleaner is in good condition before starting work. Before plugging the vacuum cleaner into the electrical mains, make sure that the voltage rating indicated on the data plate corresponds to that of the electrical mains. Plug the vacuum cleaner into a socket with a properly installed ground connection. Make sure that the vacuum cleaner is off. To carry out maintenance operations which are not described in this manual contact the manufacturer's Service Centre or our sales network. Dimensions Figure 3 Model A (in) B (in) C (in) lbs. WSS 100 22. 8 31. 5 48. 4 110 WST 100 22. 8 34. 7 48. 4 132 [ NOTE ] · · Storageconditions: Temperature:-10°C÷+40°C Humidity:85% Operatingconditions: Maximumaltitude:800m (Upto2, 000mwithreducedperformances) Temperature:-10°C÷+40°C Humidity:85% 5 09/2009 WSS100 - WST100 DV Controls, indicators and connections Figure 4 1 2 ON/OFF switches Diverter valve (WST 100 only) · · · · · Inspection prior to starting Figure 5 1 Inlet Activate the diverter valve (2), and move it to position A, in order to reverse the flow of air. Push both switches (1) to start the machine. Holding the drain hose firmly, open the valve on the drain hose to start the flow of liquid. At the end of the emptying operation push both switches (1) to stop the vacuum units. To start the vacuum operation, close the drain valve (3), take the valve (2) to B position, then push both switches (1). Do not operate the diverter valve "2" when the vacuum units are activated. If the flow is inverted when the vacuum units are activated, the machine may be damaged. Prior to starting, check that: · All latches are tightly closed; · The vacuum hose and tools have been properly fitted into the inlet (1); · The chip basket is present, · The liquid container is not full. · The float inside the liquid container is present and installed correctly Starting up Figure 6 1 Castor brakes Lock the castor brakes before starting the vacuum cleaner (1). Starting the vacuum cleaner · Push one of the switches or both of them (1 - figure 4) to start the vacuum cleaner. The related warning lights will turn on. Push the switches (1 - figure 4) once again to stop the vacuum cleaner. Stopping - Emergency stopping · Emptying the containers Figure 7 1 2 3 ON/OFF switches Diverter valve (WST 100 only) Drain valve Emptying the liquid container (WSS 100) Figure 1 · When the tank is full, the float (11-figure 1) stops the vacuuming operation; nevertheless, the vacuum motors (5-figure 1) remain activated. [. . . ] Empty the basket and clean it (see "Cleaning the containers" paragraph). Place the chip basket back in position, making sure it is correctly positioned. Maintenance, cleaning and decontamination WARNING!The precautions described below must be taken during all the maintenance operations, including cleaning and replacing of the safety filters. Check that the holes are free of dirt; clean them if necessary. Liquid container Figure 9 1 2 3 4 · · · · · · · · · Float ball and support plate Chip basket Container closing band Drain valve Empty the liquid container (see "Emptying the containers" paragraph). [. . . ]