User manual NILFISK WST 100 DV

[. . . ] 6 Inspection prior to starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Starting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Starting the vacuum cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Stopping - Emergency stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Make sure that connections to the electrical mains and plug are correct. Use the vacuum cleaner only when the cables that connect to the electrical mains are in good condition (damaged cables could lead to electric shocks!). Regularly check that the electric cable does not show signs of damage, excessive wear, cracks or aging. When the vacuum cleaner is operating: · Do not crush, pull, damage or tread on the cable that connects to the electrical mains. · Only disconnect the cable from the electrical mains by removing the plug (do not pull the cable). · Only replace the electric power cable with one of the same type as the original (H05 VV-F); the same rule applies if an extension is used. · The cable must be replaced by the manufacturer's Service Centre staff or by equivalent qualified personnel. WARNING!The vacuum cleaner's power socket must be protected by a differential circuit-breaker with surge current limitation, that shuts off the power supply when the current discharged to the ground exceeds 30 mA for 30 msec. Never spray water on the vacuum cleaner: this could be dangerous for persons and could short circuit the power supply. · · · · · 09/2009 4 WSS100 - WST100 DV Vacuuming Liquids WARNING!Comply with the safety regulations governing the materials for which the vacuum cleaner is used. · · · · Before vacuuming, check that the float is present. If foam forms, turn off the vacuum cleaner iinediately and empty the container. Warning: switch off the vacuum cleaner iinediately if foam or liquid leaks out. Warning: the dirty liquid collected by the vacuum cleaner must be considered conductive. Do not use the vacuum cleaner without the float!If it's used without the float, the vacuum cleaner may be seriously damaged. Technical specifications Parameter Voltage / frequency Power rating Noise level Protection Insulation Shaving capacity (optional) Max liquid capacity Inlet (diameter) Max vacuum Maximum air flow rate (without hose and reductions) Units V/Hz kW dB(A) IP Class gallons gallons in in H2O cfm WSS 100 / WST 100 DV 120/60 1. 6 73 44 I 6. 6 26 2 70 150 Maintenance and repairs WARNING!Disconnect the vacuum cleaner from its power source before cleaning, servicing, replacing parts or converting it to obtain another variant. · Carry out only the maintenance operations described in this manual. · Do not modify the vacuum cleaner in any way. Failure to comply with these instructions could jeopardize your safety. Moreover, such action would iinediately void the EC declaration of conformity issued with the vacuum cleaner. To carry out maintenance operations which are not described in this manual contact the manufacturer's Service Centre or our sales network. Dimensions Figure 3 Model A (in) B (in) C (in) lbs. [. . . ] The vacuum cleaner performance has decreased. Electrostatic current on the vacuum cleaner. The vacuum cleaner does not start after emptying the container. The vacuum hose is not free from debris. [. . . ]