User manual NOVAK HAVOC PRO SC

[. . . ] STEP 5-one-touch programming With ESC connected to (at least) a receiver and a charged battery pack: OPTIONAL RECEIVER PACK USAGE If you are planning to use an external receiver battery pack with the Havoc Pro SC ESC to power the electronics you need to do the following: 1. Plug the external 5 cell (1. 2VDC/cell) receiver battery pack into the battery slot of the receiver. To turn the vehicle ON, switch the receiver pack ON. Then, turn the ESC's switch ON, then OFF to allow the ESC to be powered by an external source. [. . . ] Using Li-Po/Li-Fe batteries that cannot supply the amount of current required by this system will result in possible battery pack, ESC & motor damage, and will void the warranty. It is recommended to use a 25C or higher rating. With the higher performance of brushless systems, undesirable radio system noise may occur when used with lower quality radio systems. 2. 4GHz radio systems are the best to use. FM radio systems are acceptable, as long as the system is high quality. AM radio systems are not recommended. ADDITIONAL NOTES: ACCESSORIES PLUG-IN INPUT SIGNAL HARNESS (MINI-JST) [Novak kits #5304 & #5309] BATTERY HARNESS W/ TRAXXAS® PLUG [Novak kit #5331) Traxxas@-compatible 14G plug harness for easy and low resistance connections. Included input signal harness with 2mm mini plug on ESC end for use with Havoc Pro SC. 4. 5" in Novak kit #5304, and 9" in Novak kit #5309. NO SCHOTTKy DIODES! DO NOT FREE REV OR OpERATE WITHOuT LOAD!DISCONNECT bATTERIES WHEN NOT IN uSE 2S Li-po/Li-Fe OR 4-6 Ni-MH CELLS ONLy CONTACT INFORMATION: NOVAK ELECTRONICS, INC. Irvine, CA 92614 PHONE: (949) 833-8873 · FAX: (949) 833-1631 Customer Service E-mail: cs@teamnovak. com www. teamnovak. com BRUSHLESS MOTOR CONNECTOR WIRE SET [Novak kit #5332] Flexible 14GA wire with gold-plated connectors for low-resistance connections. BRUSHLESS SENSOR HARNESSES [Novak kit #5351-#5353] SUPER-FLEX SILICONE 14GA WIRE SET [Novak kit #5508] Wiring and cooling fan This section shows the polarity of the Havoc Pro SC's output pins. The included receiver harness (Novak #5309) has a 2mm mini plug on the end that is plugged into the ESC and a standard JST plug on the receiver end. The included ON/OFF switch (Novak #5602) has a standard JST plug on it. Before connecting, note the wiring sequence of the installed harness connectors as shown here. The Havoc Pro SC's heat sink is designed to accept a 25x25mm cooling fan, and comes with nylon 4-40x5/8" screws to secure it. To install, simply center the fan on the ESC and push the nylon screws down into the cross cuts of the heat sink. If using metal screws, thread them into the heat sink. Install the fan's power connector onto the fan output pins on the ESC--note polarity as shown below. Novak #5649 installed Shielded sensor harness protects sensor wires and provides multiple installation options. 4"/100mm (Novak #5351), 6"/150mm (Novak #5352) & 9"/230mm (Novak #5353). Two each of 9" length black, red, blue, yellow and orange 14GA wire. product warranty The Havoc Pro SC Brushless ESC is guaranteed to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (verified by dated, itemized sales receipt). Optional wire set is perfect for low-resistance connections. pOWER TRANS-CAp MODuLE REQuIRED REMOTE POWER PROGRAMMING SWITCH [Novak kit #5602] 25x25x10mm COOLING FANS [Novak kits #5649 & #5653] POWER TRANS-CAP MOdULE [Novak kit #5679] Included ON/OFF Power Switch and One-Touch Programming Button harness. Cooling fans fit heat sink perfectly & has the Havoc Pro SC's 2mm mini power plug for easy connection. Single fan in Novak kit #5649, and 2-pack of fans in Novak kit #5653. [. . . ] Solder the ESC's YELLOW Phase `B' motor wire to the motor's `B' solder tab as described in Step 2B above. Solder the ESC's ORANgE Phase `C' motor wire to the motor's `C' solder tab as described in Step 2B above. IMPORTANT NOTE: dO NOT OvERHEAT SOLdER TABS Prolonged/excessive heating of solder tabs (motor or ESC) will damage PCB. Note: make sure no wire strands have strayed to an adjacent solder tab, this will result in short-circuiting & severe ESC damage, which will void the warranty. 5. [. . . ]