User manual NOVAK KINETIC SET-UP GUIDE

[. . . ] STEP 6-one-touch programming With the ESC connected to (at least) a charged battery pack, the receiver, and the brushless motor's sensor harness: OPTIONAL RECEIVER PACK USAGE If you are planning to use an external receiver battery pack with the Kinetic 2S ESC to power the electronics you need to do the following: 1. Plug the external 5 cell (1. 2VDC/cell) receiver battery pack into the battery slot of the receiver. To turn the vehicle ON, switch the receiver pack ON. Then, turn the ESC's switch ON, then OFF to allow the ESC to be powered by an external source. [. . . ] Irvine, CA 92614 PHONE: (949) 833-8873 · FAX: (949) 833-1631 Customer Service E-mail: cs@teamnovak. com www. teamnovak. com NOVAK ELECTRONICS, INC. PLUG-IN INPUT SIGNAL HARNESS (MINI-JST) [Novak kits #5304 & #5309] Includes input signal harness with 2mm mini plug on ESC end for use with Kinetic. 4. 5" in Novak kit #5304, and 9" in Novak kit #5309. DO NOT FREE REV OR OPERATE WITHOUT LOAD!DISCONNECT BATTERIES WHEN NOT IN USE 1-2S LiPo/LiFe OR 4-6 NiMH CELLS ONLY BRUSHLESS SENSOR HARNESSES [Novak kit #5351-#5353] SUPER-FLEX SILICONE 14GA WIRE SET [Novak kit #5508] Shielded sensor harness protects sensor wires and provides multiple installation options. 4"/100mm (Novak #5351), 6"/150mm (Novak #5352) & 9"/230mm (Novak #5353). Two each of 9" length black, red, blue, yellow and orange 14GA wire. Wiring and cooling fan This section shows the polarity of the Kinetic's output pins. The included receiver harness (Novak #5309) has a 2mm mini plug on the end that is plugged into the ESC and a standard JST plug on the receiver end. The included ON/OFF switch on the Kinetic 2S (Novak #5602) has a standard JST plug on it. Before connecting, note the wiring sequence of the installed harness connectors as shown here. The Kinetic 2S's heat sink is designed to accept a 25x25mm cooling fan, and comes with nylon 4-40x5/8" screws to secure it. To install, simply center the fan on the ESC and push the nylon screws down into the cross cuts of the heat sink. If using metal screws, thread them into the heat sink. Install the fan's power connector onto the fan output pins on the ESC--note polarity as shown below. Novak #5649 installed Sensor harness Receiver harness ON/OFF switch black wire (negative) red wire (positive) white wire (signal) Fan power output pins product warranty The Kinetic Racing Brushless ESC (1S or 2S) is guaranteed to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (verified by dated, itemized sales receipt). in Irvine, CA and assembled with globally sourced components. · All Rights Reserved · No part of these instructions may be reproduced without the written permission of Novak Electronics, Inc. Kinetic 2S Racing Brushless ESC, Kinetic 1S Racing Brushless ESC, Dynamic Timing Advance, Electronic Power Control, NovaBrakes, Smart Braking II, Polar Drive Technology, Radio Priority Circuitry, & One-Touch Set-Up are all trademarks of Novak Electronics, Inc. SUPER-FLEX SILICONE 12GA WIRE SET [Novak kit #5512] Two each of 3 ft. Optional wire set is perfect for low-resistance connections. BRUSHLESS MOTOR CONNECTOR WIRE SET [Novak kit #5332] LOW-PROFILE HEAT SINK [Novak kit #S5431] NO REVERSE VOLTAGE! Flexible 14GA wire with gold-plated connectors for low-resistance connections. For Kinetic/GTB 2/Havoc Pro SC ESCs with 8. 5T or higher motor. Includes thermal gap pad. POWER TRANS-CAP MODULE REQUIRED REMOTE POWER PROGRAMMING SWITCH [Novak kits #5602 & 5604] 2-PIN JST HARNESS SET--MALE & FEMALE PIGTAILS [Novak kit #5612] COOLING FANS--25x25x10mm [Novak kits #5649 & #5653] POWER TRANS-CAP MODULE [Novak kits #5679 & 5687] Includes ON/OFF Power Switch and Programming Button harness. Includes 1 male & 1 female harness with 22GA silicone wire and 2-pin JST connector on 1 end. Cooling fans fit the ESC's heat sink perfectly & has the Kinetic's 2mm mini plug for easy power connection. Single fan in Novak kit #5649, and 2-pack of fans in Novak kit #5653. Replacement Power Trans-Cap provides improved efficiency and lowers operating temperatures. [. . . ] If Power Trans-Cap Module becomes dented or damaged, ESC failure can occur--replace immediately (Novak Kit #5679 for 2S & #5687 for 1S). Schottky diodes must NOT be used with brushless ESCs. Schottky diode usage will damage the ESC & void warranty. KINETIC 1S SET-UP PHOTO 3. INSTALL ON/OFF SWITCH Use the included double-sided tape, and mount the switch where it will be easy to access--be sure to select a position where it will not get damaged or get switched OFF during a crash or roll-over. [. . . ]