User manual NOVAK PRO SC SET-UP GUIDE

[. . . ] STEP 5-one-touch programming With the ESC connected to (at least) a charged battery pack, the receiver, and the brushless motor's sensor harness: OPTIONAL RECEIVER PACK USAGE If you are planning to use an external receiver battery pack with the Havoc Pro SC ESC to power the electronics you need to do the following: 1. Plug the external 5 cell (1. 2VDC/cell) receiver battery pack into the battery slot of the receiver. To turn the vehicle ON, switch the receiver pack ON. Then, turn the ESC's switch ON, then OFF to allow the ESC to be powered by an external source. [. . . ] An external 2S Power Trans-Cap module is installed on ESC & MUST be used at all times. Failure to use a Novak Power Trans-Cap module with the proper cell rating will result in higher ESC temperatures & possible thermal shut-down or damage. Always turn on the power of the transmitter first so that you will have control of the vehicle when you turn it on. Using LiPo/LiFe batteries that cannot supply the amount of current required by this system will result in possible battery pack, ESC & motor damage, and will void the warranty. It is recommended to use a 25C or higher rating. With the higher performance of brushless systems, undesirable radio system noise may occur when used with lower quality radio systems. An FM system is acceptable, as long as it is high quality. AM systems are NOT recommended. NO SCHOTTKY DIODES! CONTACT: 17032 Armstrong Ave. Irvine, CA 92614 PHONE: (949) 833-8873 · FAX: (949) 833-1631 Customer Service E-mail: cs@teamnovak. com www. teamnovak. com NOVAK ELECTRONICS, INC. DO NOT FREE REV OR OPERATE WITHOUT LOAD!DISCONNECT BATTERIES WHEN NOT IN USE 2S LiPo/LiFe OR 4-6 NiMH CELLS ONLY BRUSHLESS MOTOR CONNECTOR WIRE SET [Novak kit #5332] BRUSHLESS SENSOR HARNESSES [Novak kit #5351-#5353] LOW-PROFILE HEAT SINK [Novak kit #S5431] Flexible 14GA wire with gold-plated connectors for low-resistance connections. Shielded sensor harness protects sensor wires and provides multiple installation options. 4"/100mm (Novak #5351), 6"/150mm (Novak #5352), & 9"/230mm (Novak #5353). Wiring and cooling fan This section shows the polarity of the Havoc Pro SC's output pins. The included receiver harness (Novak #5309) has a 2mm mini plug on the end that is plugged into the ESC and a standard JST plug on the receiver end. The included ON/OFF switch (Novak #5602) has a standard JST plug on it. Before connecting, note the wiring sequence of the installed harness connectors as shown here. The Havoc Pro SC's heat sink is designed to accept a 25x25mm cooling fan, and comes with nylon 4-40x5/8" screws to secure it. To install, simply center the fan on the ESC and push the nylon screws down into the cross cuts of the heat sink. If using metal screws, thread them into the heat sink. Install the fan's power connector onto the fan output pins on the ESC--note polarity as shown below. Novak #5649 installed product warranty The Havoc Pro SC Brushless ESC is guaranteed to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (verified by dated, itemized sales receipt). Includes thermal gap pad. SUPER-FLEX SILICONE 14GA WIRE SET [Novak kit #5508] SUPER-FLEX SILICONE 12GA WIRE SET [Novak kit #5512] Two each of 9" length black, red, blue, yellow, and orange 14GA wire. Optional wire set is perfect for low-resistance connections. NO REVERSE VOLTAGE! POWER TRANS-CAP MODULE REQUIRED REMOTE POWER PROGRAMMING SWITCH [Novak kit #5602] 25x25x10mm COOLING FANS [Novak kits #5649 & #5653] POWER TRANS-CAP MODULE [Novak kit #5679] Includes ON/OFF Power Switch and One-Touch Programming Button harness. Cooling fans fit heat sink perfectly & has the Havoc Pro SC's 2mm Mini power plug for easy connection. [. . . ] Solder the ESC's YELLOW Phase `B' motor wire to the motor's `B' solder tab as described in Step 3B above. Solder the ESC's ORANGE Phase `C' motor wire to the motor's `C' solder tab as described in Step 3B above. IMPORTANT NOTE: DO NOT OVERHEAT SOLDER TABS Prolonged/excessive heating of solder tabs (motor or ESC) will damage PCB. Note: Make sure no wire strands have strayed to an adjacent solder tab, this will result in short-circuiting & severe ESC damage, which will void the warranty. 5. [. . . ]