User manual OCTEK SOCKET ROCKET 336 COMMAND CARD

[. . . ] Socket Rocket 336 COMMAND CARD Connection Commands Command A D H O Description Answer call Dial number Hang up modem Enter On-line state s Indicates factory defaults v Changing the default is not allowed by Austel If no value is entered in a command for `n' or `x', a value of 0 is selected. TM Dial Modifiers Dial Digits , F or ^ L P R S=n T W ; ! [. . . ] Display value in S Register `n' Place `x' in S Register `n' Tone dialling Numeric response codes 2 Verbal response codes W0 W1 W2 X0 X1 X2 X3 X4 X5 X6 Zn &C0 &C1 &C2 &D0 &D1 &D2 &D3 &F0 &F1 &F. &G0 &G1 &G2 &K0 &K3 &K4 &K5 &K9 &M0 &M4 &N0 &N1 &P0 &P1 &S0 &S1 &S2 &T0 &T1 &T3 &T4 &T5 &T6 &T7 s s s s s s s s sv s CONNECT message reports the terminal speed CONNECT message reports the terminal speed CONNECT message reports the line speed Basic response codes (codes 0-4, 8) Extended response codes (codes 0-5, 8, 10-12, 30-40, 60-62) Extended response codes (codes 0-6, 8, 10-12, 30-40, 60-62) Extended response codes (codes 0-5, 7, 8, 10-12, 30-40, 60-62) Extended response codes (codes 0-7, 10-12, 30-40, 60-62) Extended response codes (codes 0-7, 10-13, 30-40, 60-62) Extended response codes (codes 0-5, 7-8, 10-13, 30-40, 60-62) Restore configuration profile n (n=0, 1, 2, 3) DCD signal always asserted DCD signal responds to remote modem DCD signal always on, pulses low on disconnect Ignore DTR Return to Local command state if DTR goes low Hang up and return to Local command state if DTR goes low, disable auto-answer until DTR asserted Initialise with values in &Y profile if DTR goes low Restore factory defaults Restore non-error correction factory defaults Reset modem (clear security database/Telephone numbers) No guard tone generated 550 Hz guard tone generated 1800 Hz guard tone generated Flow control disabled RTS/CTS flow control XON/XOFF flow control Transparent XON/XOFF flow control Failsafe flow control Asynchronous mode Asynchronous mode with stored number dialling Abort dial character disabled Abort dial character enabled 39/61 make/break ratio (USA) 33/67 make/break ratio (Aus/UK) DSR signal always asserted DSR signal asserted at start of handshake DSR signal asserted at end of handshake (before CONNECT message) Terminate test Local Analog Loopback test Local Digital Loopback test Grant Remote Digital Loopback test Deny Remote Digital Loopback test Remote Digital Loopback test 3 Remote Digital Loopback & Self test &T8 &V &Vn &V8 &Wn &Yn &Zn=x #A0 #A1 #A2 s #B0 s #B1 #C0 #C1 s #E0 s #E1 #E2 #J0 #J1 s #O0 s #O1 #O2 #O3 #S #V0 #V1 s %B0 s %B1 %C0 %C1 %C2 %C3 s %Dn %E0 %E1 %E2 s %K0 s %K1 %L0 %Ln %P0 s %P1 %Q %R0 s %R1 %R2 %S0 s Local Analog Loopback & Self test View active configuration profile View stored profile (n=0-3) View differences between active and default Save current configuration into stored profile n (n=0, 1, 2, 3) Select stored profile n for Power on and &D3 Store x as phone number n (x=0-9) Prevent remote access Allow remote access Allow remote access with security password In 1200bps originate mode B0=V. 23, B2=V. 22 In 1200bps originate mode B0=V. 22, B2=V. 23 V. 25 calling tones disabled V. 25 calling tones enabled DES encryption disabled DES encryption enabled Super secure enabled Assume V. 42 compatibility Check V. 42 compatibility Characters ignored if modem buffers overflow Disconnects if terminal buffer overflows Disconnects if line buffer overflows Disconnects if either buffer overflows Enter security menu mode Command and S Register verifier off Command and S Register verifier on S0=0 setting after AT&F S0=2 setting after AT&F Compression disabled MNP 5 compression enabled V. 42bis data compression enabled V. 42bis data compression enabled with fallback to MNP 5 Set disconnect delay to n seconds (default %D0) Disable auto-retrain Enable auto-retrain Automatic Speed Stepping CTS operates normally CTS off during dial and handshake Report current received signal level (-dBm) Set transmit level (n=11 to 19; -11dBm to -19dBm) CONNECT message appears before DCD asserted CONNECT message appears after DCD asserted Report current line quality (EQM) (0=perfect) &R command determines state of CTS CTS always follows RTS (not reset by &F) CTS follows DTR when offline (not reset by &F) 4 DSR is not overridden LP R * EA S Y C %S1 %T0 s %U0 s %U1 %U2 %W0 s %W1 \A0 \A1 \A2 \A3 s \Bn \J0 s \J1 \Kn \N0 \N1 \N2 \N3 s \N4 \N5 \N6 \N7 \Q0 \Q1 \Q2 \Q3 \Q4 \Q5 \Q6 \S \Tn \V0 s \V1 \V8 \V9 \X0 s \X1 *A0 *A1 s *A2 *Wttt. . . tt DSR mimics the state of DTR (not reset by &F) DCD always follows state of carrier Standard error correction response codes V. 42 response codes when V. 42 connection established V. 42 response codes for V. 42 connections, MNP 2, 4, compression & DES messages displayed Disable welcome message Send message specified by *W to remote modem after connect MNP block size = 64 MNP block size = 128 MNP block size = 192 MNP block size = 256 Send Break sequence to remote modem (default \B3) Fallback to direct mode disabled Fallback to direct mode enabled Received Break control (default \K5) Constant speed mode Variable speed mode MNP reliable mode V. 42/MNP auto-reliable mode V. 42 reliable mode V. 42 auto-reliable mode V. 42/MNP reliable mode, fallback to MNP reliable mode MNP auto-reliable mode Flow control disabled XON/XOFF flow control from modem and computer CTS flow control CTS-RTS flow control (same as &K3) Modem-only XON/XOFF flow control CTS flow control (CTS low until connection) CTS-RTS flow control - CTS low until connect Display active configuration with detailed description Set inactivity timer to n seconds (Default \T0) Disable reliable response codes Enable reliable response codes Extended response codes Extended response codes with diagnostic information XON/XOFF pass through disabled XON/XOFF pass through enabled Conservative Automatic Rate Selection Medium Automatic Rate Selection Aggressive Automatic Rate Selection Specify welcome message text used by %W1 ttt. . . tt = text use | for new line (max. 80 characters) S Registers Reg 0 1 2 3 4 5 6 7 8 9 10 11 12 16 18 25 26 27 29 30 33 38 42 43 62 66 67 69 74 Range 0-255 0-255 1-255 0-127 0-127 0-127 4-7 1-60 1-7 1-255 1-255 70-254 3-255 0-8 0-255 0-255 0-255 0-255 10-100 0-255 0-1 0-255 0-255 0-255 0-255 1-255 1-127 0-255 0-255 Def Unit 0 rings 00 rings 43(+) ASCII 13 ASCII 10 ASCII 08 ASCII 04 secs 30 secs 04 secs 06 0. 1secs 18 0. 1secs 95 msecs 50 0. 02secs 00 00 secs 05 0. 01secs 00 0. 01secs 00 secs 50 0. 01secs 00 10secs 1 00 secs 15 75 10 42(*) 60 msecs 0. 01secs 0. 1secs ASCII secs Function Rings Before Answer Ring Count (read only) Escape Sequence Character Carriage Return Character Line Feed Character Backspace Character Wait for Dial Tone Wait for Carrier Delay for Pause Modifier Carrier Detect Response Time (fsk only) Lost Carrier/Hang Up Delay (fsk only) Touch Tone Timing Escape Sequence Guard Time Test in Progress (read only) Test Timer DTR Loss Detection Time RTS-CTS Delay Delay Before Security Dial-back Hook Flash Duration (also sets S100) Inactivity Timer (data mode) Retrain Disable = 0 Disconnect Delay Modem Disconnect Reason (read only) Break Sequence Length V. 42 detection timer Remote Access Guard Time Remote Access Character Command line timeout Disconnect Reason Previous Call Distinctive Ring AT-SDR=n, AT-SDR=0 AT-SDR=1 AT-SDR=2 AT-SDR=3 AT-SDR=4 AT-SDR=5 AT-SDR=6 AT-SDR=7 where n=0 to 7, default=0 Any ring detected and reported as "RING" Single ring detected and reported as "RING1" Double ring detected and reported as "RING2" Single and Double ring detected and reported as "RING1" or "RING2" Triple ring detected and reported as "RING3" Single and Triple ring detected and reported as "RING1" or "RING3" Double and Triple ring detected and reported as "RING2" or "RING3" Any ring detected and reported as "RING1" or "RING2" or "RING3" Use AT-SDR=4 for Telstra's Duet service. Do not set Auto Answer below 2 when Distinctive Ring is enabled. Response Codes Num 0 1 2 3 4 6 7 8 13 20 22 23 24 Verbal OK CONNECT RING NO CARRIER ERROR NO DIALTONE BUSY NO ANSWER RINGING CONNECT/REL CONNECT 1200/REL CONNECT 2400/REL CONNECT 4800/REL Description Command accepted Connection established Incoming call detected Carrier not detected Command error Dial tone not detected, check phone connection The number dialled is busy Silence not detected The number dialled is ringing Connection established error corrected Connected at 1200 bps error corrected Connected at 2400 bps error corrected Connected at 4800 bps error corrected 7 75 80 81 82 95 96 97 100 0-255 1-19 1-19 1-255 0-63 1-255 1-255 1-10 0 0. 01secs DTR active detection time 15 5% Flow Control High Water Mark 03 5% Flow Control Low Water Mark 60 bytes Failsafe Flow Control Overrun 0 bitmap Extended Result Codes 80 Help Page Width 24 Help Page length 5 100msecs Hook Flash Duration (also sets S29) 5 Use AT?to see the Command Set supported by your modem's version of code. [. . . ] 6 28 25 26 27 43 44 45 46 47 48 96 98 49 50 70 71 72 5 10 11 32 12 30 31 33 34 35 36 37 38 95 97 39 40 60 61 62 63 CONNECT 7200/REL CONNECT 9600/REL CONNECT 12000/REL CONNECT 14400/REL CONNECT 16800/REL CONNECT 19200/REL CONNECT 21600/REL CONNECT 24000/REL CONNECT 26400/REL CONNECT 28800/REL CONNECT 31200/REL CONNECT 33600/REL CONNECT 38400/REL CONNECT 57600/REl CONNECT 76800/REL CONNECT 96000/REL CONNECT 115200/REL CONNECT 1200 CONNECT 2400 CONNECT 4800 CONNECT 7200 CONNECT 9600 CONNECT 12000 CONNECT 14400 CONNECT 16800 CONNECT 19200 CONNECT 21600 CONNECT 24000 CONNECT 26400 CONNECT 28800 CONNECT 31200 CONNECT 33600 CONNECT 38400 CONNECT 57600 CONNECT 76800 CONNECT 96000 CONNECT 115200 CONNECT 230400 Connected at 7200 bps error corrected Connected at 9600 bps error corrected Connected at 12000 bps error corrected Connected at 14400 bps error corrected Connected at 16800 bps error corrected Connected at 19200 bps error corrected Connected at 21600 bps error corrected Connected at 24000 bps error corrected Connected at 26400 bps error corrected Connected at 28800 bps error corrected Connected at 31200 bps error corrected Connected at 33600 bps error corrected Connected at 38400 bps error corrected Connected at 57600 bps error corrected Connected at 76800 bps error corrected Connected at 96000 bps error corrected Connected at 115200 bps error corrected Connected at 1200 bps Connected at 2400 bps Connected at 4800 bps Connected at 7200 bps Connected at 9600 bps Connected at 12000 bps Connected at 14400 bps Connected at 16800 bps Connected at 19200 bps Connected at 21600 bps Connected at 24000 bps Connected at 26400 bps Connected at 28800 bps Connected at 31200 bps Connected at 33600 bps Connected at 38400 bps Connected at 57600 bps Connected at 76800 bps Connected at 96000 bps Connected at 115200 bps Connected at 230400 bps YPT125-3B 8 © 1996 NetComm Limited [. . . ]