User manual OKI OF 5050

[. . . ] OKIFAX 5050 Handbook OF5050M. PM6 1 4/15/98, 9:23 AM Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Okidata assumes no responsibility for the results of errors beyond its control. Okidata also cannot guarantee that changes in products made by other manufacturers and referred to in this handbook will not affect the applicability of the information in it. This handbook is subject to change without notification. [. . . ] Your OKIFAX feeds the document the rest of the way through the document feeder. If the line is busy or if there is no answer, your OKIFAX will wait, and then automatically redial the number. The dial parameter settings determine how many times it will redial and how long it will wait between attempts--see page 54 for details. Also, if your OKIFAX is transmitting from memory and a communication error occurs, it will automatically redial the number and try to resend the fax. Shortcut Fax Number Programming This convenient feature lets you program a number into your OKIFAX for future use while you're sending a fax to it. It even finds the first available One Touch key (or Auto Dial number, if all the One Touch keys are programmed) for you to program. Faxing: Basic Operations 35 Of5050hw. pm6 35 4/15/98, 9:32 AM Use the following procedure: 1 2 3 Load the document. Enter the fax number using the numerical keypad. The number in brackets is the next unprogrammed One Touch key number. If all the One Touch keys are programmed, the display shows AUTO DIAL NO. [01], with the number of the next unprogrammed Auto Dial number. Press Yes to program the location to the number shown. Or press Search to cycle through the available unprogrammed keys/numbers, then press Yes to program to the number you want. The display reads NO=5551212 [the fax number you entered] ID=. Press Start, then enter the location ID. This is a descriptive title up to 15 characters long. Refer to the instructions below. To Do This Enter numbers Enter spaces Enter hyphens (-) Use Numeric keypad (press once) Space One Touch key Hyphen key Enter a unique character Press the 0/Unique key repeatedly until the character you want appears. The following characters are available: !· ä ß ñ ö ü Æ Å Ø æ å ø. Yes and No key to move to the next Enter two successive letters/numbers on the same key Move the cursor to make corrections keys 6 7 Press Start. The display shows PROGRAMMING, then DIALING, and the OKIFAX dials the number and sends the fax. 4 Receiving Faxes Manually If your OKIFAX is set to the manual receive [TEL] mode, it treats all incoming calls as voice conversations, and does not automatically receive faxes. Note: You must have a handset connected to the OKIFAX in order to receive faxes manually. 5 To receive a fax while in manual receive mode: 1 When your telephone or fax machine rings, pick up the telephone handset connected to it. If a person is on the line, carry on your conversation. If a remote fax machine is on the line, or if a person wishes to fax you a document after a conversation, press the Start key. Enter alphabetical Locate the character you want on the numeric characters keypad. Press that key repeatedly until the character appears on the display. 2 36 Of5050hw. pm6 Faxing: Basic Operations 36 4/15/98, 9:32 AM 3 4 When the RECEIVING message appears on the display, hang up the handset. After you receive the fax, a long beep tells you that the transmission was successful. 1 Canceling Messages Stored in Memory It is possible to erase messages received in memory without printing them. [. . . ] Toner gets in the eyes. CAS# 67762-90-7 OSHA PEL 15. 0 mg/m3 for total dust ACGIH TLV 10. 0 mg/m3 for total dust Note: Note: This product is not regulated under Section 313 of SARA, Title III. Physical Data Melting Point: 110°C (230°F) Boiling Point: Not applicable Vapor Pressure: Not applicable Of5050hw. pm6 84 4/15/98, 9:45 AM Vapor Density (Air=1): Not applicable Evaporation Rate (Butyl Acetate=1): Not applicable Specific Gravity (H2O=1): 1. 15 Solubility in water: Negligible Appearance and odor: Black granules, no odor Health Hazard Data Routes of Entry: Inhalation, Ingestion, Eyes, Skin. Health Hazards: Fire and Explosion Hazard Data Flash Point (Method Used): Not applicable Flammable Limits Lower Explosive Limit: Not applicable Upper Explosive Limit: Not applicable Extinguishing Media: Water, CO2, Dry Chemical, or Foam Special Fire Fighting Procedures: Do not use methods that may create a dust cloud, such as high pressure water and/or steam Unusual Fire and Explosion Hazards: · Organic components decompose at 200-455°C (392851°F). · Material may explosively combust when finely suspended in air. · Thermal decomposition of organic components may result in release of oxides of carbon and nitrogen. 1. Styrene-Butyl Acrylate Copolymer Subcutaneous implantation of polymeric styrene powder in rats has induced tumors at the site of implantation. [. . . ]