User manual OKI OKIPAGE 18 NETWORK CARD

[. . . ] OkiLAN 6100e+® User's Guide High Performance Ethernet Network Print Server Copyright and Trademark Information Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Oki Data assumes no responsibility for the results of errors beyond its control. Oki Data also cannot guarantee that changes in products made by other manufacturers and referred to in this handbook will not affect the applicability of the information in it. This handbook is subject to change without notification. [. . . ] For example, kill -USR1 <process id of bootpd>. Check your documentation for more information. · Check the system's syslog file. Some BOOTP servers will write error messages into the syslog file. Example: Sep 6 14:38:43 bootpd[17565]: hardware address not found: 004068175042 This message appears when the BOOTP server received a request from a device not in its internal bootptab tables. IV - 50 OKI OkiLAN 6100e+ User's Guide Section 4 - Appendix A - Troubleshooting Static Route Entry If the OkiLAN 6100e+ has printed a configuration page showing the default address, but it cannot be reached through telnet, check the following: · Display the host's routing tables with the `netstat r' command. Verify the route has been set correctly. · If the route is set correctly, try pinging the device. · Verify the OkiLAN 6100e+ is on the same subnet as the host from which you are telneting. As a drastic measure, try creating an isolated subnet with your host and the OkiLAN 6100e+. If you are using 10BASE2, run the cable directly from the host to the OkiLAN 6100e+. If using 10BASE-T cabling, connect the host to the OkiLAN 6100e+ through a hub not connected to any other host. · If the static route has been set up and can telnet to the OkiLAN 6100e+, but your changes do not seem to be saved, check the host's routing tables. You might have telneted to a different OkiLAN 6100e+ than the one you intended. While in telnet, select the second menu option, Show Network/Printer Information. The hardware address and serial number are displayed. Verify they are the same as the unit you are configuring. · Turn off the OkiLAN 6100e+ you want to configure. If you reach a different device, there is an IP address conflict. · If you are able to ping to the OkiLAN 6100e+, but are unable to telnet, the IP address is probably being shared with another device that does not support telnet. OKI OkiLAN 6100e+ User's Guide IV - 51 TCP/IP Section 4 - Appendix A - Troubleshooting OkiNet for TCP/IP - Winsock Errors · If you see an error before OkiNet for TCP/IP appears on the screen, try setting a host name in the hosts file in the Windows directory (check the documentation for your Windows TCP/IP stack). · If you have difficulty seeing a particular OkiLAN 6100e+, try moving the device onto the same subnet as the computer running the utility. · If OkiNet for TCP/IP gives you the Winsock error: Could not bind to socket, use the Special Options dialog under the File menu to change the Discovery UDP Port to a different port number. Hardware Error Messages ST: Cable not connected Self-test has determined that the network cable is not connected. · Check the cable connection to the OkiLAN 6100e+. [. . . ] Infrared port on notebook or mobile device meeting the IrDA standard. Infrared print drivers on the mobile device. Infrared print drivers are provided through third parties for PCs using Windows 95/98 operating systems or by generic drivers within Palm OS printing utilities. Windows CE and Windows 98 users should have the appropriate compatible drivers built in to the operating system, but the mobile device must be configured for infrared printing. For more information on system requirements, check www. okidata. com or call 1-800-OKIDATA. X-4 OKI OkiLAN 6100e+ User's Guide Section X - Chapter 2 - Installation and Configuration Chapter 2 Installation and Configuration Installing the Hardware To install the IR Transceiver, attach the DIN-6 connector on the back of the OkiLAN 6100e+ print server. General Information on Configuring Your Print Server for IR If you wish to print via infrared to an IrDA-capable printer, you need to redirect an existing printer driver to use the infrared printer port. [. . . ]