User manual OKI OKIPAGE 18N QUICK START GUIDE

[. . . ] Quick Start Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Okidata assumes no responsibility for the results of errors beyond its control. Okidata also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information in it. Mention of software products manufactured by other companies does not necessarily constitute endorsement by Okidata. [. . . ] 5 Press /Reset repeatedly until the language you want appears on the display. An asterisk appears next to the language. The printer saves the new setting and exits the menu. Set the Power Save Delay & Quiet Mode The Power Save Delay and Quiet Mode settings save energy and provide quieter operation when the printer is not printing. However, when these settings are engaged and a print job is received, the printer must warm up before printing. ! For more information, see Adjusting the Warm-up Cycle under Printer Menus in the Printer Control section of the User's Guide. Factory settings: Power Save Delay = 5 minutes, Quiet Mode = ON. Quick Start | E-31 ! For the fastest possible time to print, set the Power Save Delay to disabled and the Quiet Mode to OFF. ! If you are not changing the Quiet Mode setting, skip to step 11. To change these settings: 1 Press ON LINE. 2 Press and hold MENU 1/Menu 2 for 2 seconds. PRINT MODE appears on the display. ! If you are not changing the Power Save Delay setting, skip to step 7. 3 Press MENU 1/Menu 2 repeatedly until POWER SAVING appears on the display. The current Power Save Delay setting appears on the display. 5 Press /Reset repeatedly until the setting you want appears on the display (0 SEC, 1, 5, 10, 15, 30, 60 or 120 MIN, or disabled). An asterisk appears next to the new setting. 7 Press MENU 1/Menu 2 repeatedly until QUIET MODE appears on the display. The current Quiet Mode setting appears on the display. 9 Press /Reset to change the setting (ON or OFF). An asterisk appears next to the new setting. The printer saves the new setting(s) and exits the menu E-32 | Quick Start Set the Emulation The printer comes from the factory set to automatically switch emulations, depending on what it detects in the incoming data. If you prefer, you can set the printer for a specific emulation (HP® LaserJet® 5 PCL5e® HP LaserJet 5 PCLXL, Adobe® PostScript® Level 2, IBM® Proprinter® III XL, or Epson® FX). For information on how to do this, see Select an Emulation under Printer Menus in the Printer Control section of the User's Guide. , Print the Font Page If you wish to print out a typeface list showing samples of the resident fonts available for the various emulations: 1 Press ON LINE. 2 Press and hold TRAY TYPE/Print Fonts until PRINT FONTS appears on the display. 3 Press /Reset until the emulation for which you wish to print the font samples appears on the second line of the display. The typeface list for the selected emulation prints. The printer goes back on line, ready to receive data. Quick Start | E-33 8 Overview Driver & Software Install the The OKIPAGE 18 CD Available Choices for Macintosh Systems Adobe PostScript Level 2 Driver Required to use all the printer features. No CD-ROM Drive? See the end of this Quick Start. Available Choices for PC Systems Drivers OKIPAGE 18 Driver (HP LaserJet 5 PCL5e emulation) OKIPAGE 18 PCL-XL Driver (HP LaserJet 5 PCLXL emulation) Adobe PostScript Level 2 Driver · · · On-Line Registration (English only) For registering your printer online or by fax. E-34 | Quick Start Installation for PC Systems Available Installations Typical Select Typical to install the OKIPAGE 18 driver (PCL5e) and the on-line Registration Program (English only). Custom Select Custom if you wish to select the components to be installed. You will be allowed to pick from a listing of all available components: make sure a check mark ( ) appears in the box beside any component you wish to install. Available Registration Options You can register your printer in any of the following ways: on-line at the Okidata web site: http://www. okidata. com via modem, using the on-line registration program (English only) via fax (314-827-5421), using the on-line registration program (English only) to fill in and print out the registration form, or using the printed registration form provided with the printer via mail, using the printed registration form provided with the printer · · · · Quick Start | E-35 Installation for Windows® 95, 98, NT 4. 0 1 2 3 4 5 Insert CD in CD-ROM drive. Click Start on the Windows taskbar, then select Run. [. . . ] Once in the menu, press to move to the next menu item or hold to cycle backwards through the menu items. Press and hold 2-3 sec: Enters the Level-2 menu. Press: In menu mode, returns to the previous item. Press and hold to move backwards through items within a category. Used with /Reset to generate a drum cleaning page. [. . . ]