User manual OLIVETTI D-COPIA 16W

[. . . ] MODEL d-Copia 16W d-Copia 20W DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL · BEFORE USING THE MACHINE · COPY FUNCTIONS · PRINTER FUNCTIONS · USER SETTINGS Page 8 18 29 31 · TROUBLESHOOTING 40 · ROUTINE MAINTENANCE 55 d-Copia 16W · PERIPHERAL DEVICES AND SUPPLIES · APPENDIX 58 60 d-Copia 20W PUBLICATION ISSUED BY: Olivetti S. p. A. Gruppo Telecom Italia Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivetti. com Copyright © 2005, Olivetti All rights reserved May 2005 The mark affixed to the product certifies that the product satisfies the basic quality requirements. The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U. S. registered mark. The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment. Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product: · incorrect electrical power supply; · incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User's Manual supplied with the product; · replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel. All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. Do not make copies of anything which is prohibited from copying by law. [. . . ] (p. 19) Make sure that the SPF indicator is lit. To adjust the automatic exposure level for copies made from originals placed on the document glass, proceed to step 2. 4 Press the [Light] key ( ) or [Dark] key ( ) to lighten or darken the automatic exposure level as desired. 135 Note 2 3 Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to select "PHOTO" ( ). Hold down the [AUTO/TEXT/PHOTO] key ( AUTO / / ) until the AUTO indicator ( AUTO ) blinks. AUTO 5 Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to complete the setting. The AUTO indicator ( AUTO ) stops blinking and lights steadily. 135 The exposure level indicators show the current setting. Note After adjusting the automatic exposure level, it is recommended that you make a test copy to check the new level. 31 TONER SAVE MODE AND HIGH IMAGE QUALITY MODE Toner save mode can be enabled to reduce toner consumption by about 10%. The high image quality mode improves copy image quality in the automatic and manual exposure modes by increasing copy density with a slight increase of toner consumption. To switch between toner save mode and high image quality mode, follow the steps below. Note In Europe, high image quality mode is initially selected. In regions other than Europe, toner save mode is initially selected. 1 Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to select "TEXT" ( ). Hold down the [AUTO/TEXT/PHOTO] key ( AUTO / / ) until the PHOTO indicator ( ) blinks. AUTO 2 135 The exposure level indicators show the current setting. 3 To enable toner save mode, press the [Light] key ( ). To enable high image quality mode, press the [Dark] key ( ). 135 When enabling toner save mode, make sure that "1" is lit. When enabling high image quality mode, make sure that "5" is lit. 4 Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to complete the setting. The PHOTO indicator ( lights steadily. ) stops blinking and 32 CUSTOMISING SETTINGS (User programs) The user programs allow you to customise the machine to match your needs. USER PROGRAMS Program number Program name Setting codes (factory default setting appears in bold) 1: OFF 2: 10 sec. Explanation · "Auto clear time" automatically returns the copy settings to the initial settings (p. 12) when a certain period of time elapses after a copy is made. This program is used to select the period of time. "Auto clear time" can also be disabled. · This function automatically switches the machine to a low power consumption state if the set duration of time elapses without the machine being used when the power is on. The POWER SAVE indicator ( ) lights up, however, the keys on the operation panel can be used. Normal operation automatically resumes when a key on the operation panel is pressed, a print job is received or an original is placed. · This function automatically switches the machine to a state that consumes even less power than preheat mode if the set duration of time elapses without the machine being used when the power is on. All lights except the POWER SAVE indicator ( ) and ON LINE indicator ( ) go off. To resume normal operation, press the [START] key ( ). Normal operation also resumes automatically when a print job is received. While in auto power shut-off mode, no keys (except the [START] key ( )) can be used. · When copying using the SPF, during the period of time that the SPF indicator blinks after an original has been scanned (about 5 seconds), a subsequent original can be placed and automatically fed into the machine. · Use this setting to enable or disable auto power shut-off. [. . . ] 49 - Machine (transfer area). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 - SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 - Tray (Lower paper tray). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 - Tray (Upper paper tray). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]