User manual OLIVETTI D-COPIA 283MF

[. . . ] d-Copia 283MF d-Copia 283MF Plus d-Copia 284MF OPERATION GUIDE GB 551001en PUBLICATION ISSUED BY: Olivetti S. p. A. Gruppo Telecom Italia Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivetti. com Copyright © 2009, Olivetti All rights reserved The mark affixed to the product certifies that the product satisfies the basic quality requirements. The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U. S. registered mark. The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment. Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product: · incorrect electrical power supply; · incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User's Manual supplied with the product; · replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel. All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. Introduction Thank you for your purchase of d-Copia 283 MF/d-Copia 284 MF. [. . . ] Menu/Count. : a b 4 User/Job Account 5 User Property 6 Common Settings ********************* [ Exit ] 1 In the Sys. menu, press the key to select [Common Settings]. or Common Settings: a b 1 Language ********************* 2 Default Screen 3 Sound [ Exit ] 2 Press the OK key. The Common Settings menu appears. 3 Function Default: a b 1 Color Selection ********************* 2 Scan Resolution 3 FAX Resolution [ Exit ] Press the or key to select [Function Default]. 4 Press the OK key. The Function Default menu appears. 5 Press the or key to select [Detail Setting]. 8-44 OPERATION GUIDE Default Setting (System Menu) Detail Setting: ab 1 2 in 1 layout ********************* 2 4 in 1 Layout 3 Border Line [ Exit ] 6 Press the OK key. The Detail Setting menu appears. 7 2 in 1 Layout ab 1 *g L to R f T to B ********************* 2 e R to L Press the or key to select [2 in 1 Layout]. 8 Press the OK key. 2 in 1 Layout appears. 9 Press the or key to select [g L to R f T to B] or [e R to L]. screen returns to the Detail Setting menu. 10 Press the OK key. is displayed and the 4 in 1 Layout Select the default value for layout when [4 in 1] is selected for Combine. Items available for the default value are as follows: Item h Right then Down i Down then Right j Left then Down k Down then Left Description Arranges from upper left to right. Arranges from upper right to bottom. 8 Use the procedure below to select the default value for layout. Sys. Menu/Count. : a b 4 User/Job Account 5 User Property 6 Common Settings ********************* [ Exit ] 1 In the Sys. menu, press the key to select [Common Settings]. or OPERATION GUIDE 8-45 Default Setting (System Menu) Common Settings: a b 1 Language ********************* 2 Default Screen 3 Sound [ Exit ] 2 Press the OK key. The Common Settings menu appears. 3 Function Default: a b 1 Color Selection ********************* 2 Scan Resolution 3 FAX Resolution [ Exit ] Press the or key to select [Function Default]. 4 Press the OK key. The Function Default menu appears. 5 ab Detail Setting: 1 2 in 1 layout ********************* 2 4 in 1 Layout 3 Border Line [ Exit ] Press the or key to select [Detail Setting]. 6 Press the OK key. The Detail Setting menu appears. 7 4 in 1 Layout: ab 1 *h Right then Down ********************* 2 i Down then Right 3 j Left then Down Press the or key to select [4 in 1 Layout]. 8 Press the OK key. 4 in 1 Layout appears. 9 Press the or key to select [h Right then Down], [i Down then Right], [j Left then Down] or [k Down then Left]. screen returns to the Detail Setting menu. 10 Press the OK key. is displayed and the 8-46 OPERATION GUIDE Default Setting (System Menu) Border Line Select the default value for border line when [2 in 1] is selected for Combine. Items available for the default value are as follows: Item None l Solid Line m Dotted Line n Positioning Mark No border line. Puts a mark on the border line position. Description Use the procedure below to select the default value for border line. Sys. Menu/Count. : a b 4 User/Job Account 5 User Property 6 Common Settings ********************* [ Exit ] 1 In the Sys. [. . . ] SMTP (Simple Mail Transfer Protocol) A protocol for E-mail transmission over the Internet or an intranet. It is used for transferring mail between mail servers as well as for sending mail from clients to their servers. Status Page The page lists machine conditions, such as the memory capacity, total number of prints and scans, and paper source settings. Subnet Mask The subnet mask is a way of augmenting the network address section of an IP address. [. . . ]