User manual OLIVETTI D-COPIA 16

[. . . ] Copier Operation Manual d-Copia 16 d-Copia 200 Please read the Operation Guide before using the copier. Keep it close to the copier for easy reference. PUBLICATION ISSUED BY: Olivetti Tecnost, S. p. A. Divisione Business Prodotti Office Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivettitecnost. com Copyright © 2004, Olivetti All rights reserved March 2004 The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U. S. registered mark. The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment. The mark affixed to the product certifies that the product satisfies the basic quality requirements. Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product: · · · incorrect electrical power supply; incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User's Manual supplied with the product; replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel. In areas of the GEEA, the available setting for the Off Mode to engage is between 1 and 120 minutes, and the available setting for the Low Power Mode to engage is any 1 minute, 5 minutes, 15 minutes, 30 minutes, 45 minutes, 60 minutes, 90 minutes or 120 minutes. All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. [. . . ] on: Enabled oFF: Disabled* AtI: Automatic Detection in Inch units (*AtI: Inch specifications) AtC: Automatic Detection in centimeter units (AB columns) (*Atc: Metric specifications) o2r: Oficio II 6-20 F16 Auto Sizing 6-21 F17 F18 F19 F20 F21 Drawer Paper Size (Drawer 1) Drawer Paper Size (Drawer 2) Drawer Paper Size (Drawer 3) Drawer Paper Size (Drawer 4) Multi-bypass Tray Paper Size 6-21 [Inch specifications] UnI: Universal Size* Ldr: Ledger Horizontal LGr: Legal Horizontal Ltr: Letter Horizontal LtE: Letter Vertical Str: Statement Horizontal Cu1: Custom 1 Cu2: Custom 2 [Metric specifications] UnI: Universal Size* A3r: A3 Horizontal A4r: A4 Horizontal A4E: A4 Vertical A5r: A5 Horizontal b4r: B4 Horizontal b5r: B5 Horizontal For: Folio Horizontal Cu1: Custom 1 Cu2: Custom 2 6-22 6-8 Section 6 COPIER MANAGEMENT Display Items F22 F23 Settings Items Custom 1 Size Custom 2 Size Description Sets the size to be set to the Custom size (1 - 2). * This makes it possible to set the size that do not appear on the operation panel. Available settings [Inch specifications] A3r: A3 Horizontal A4r: A4 Horizontal A4E: A4 Vertical A5r: A5 Horizontal b4r: B4 Horizontal b5r: B5 Horizontal b5E: B5 Vertical b6r: B6 Horizontal* A6r: A6 Horizontal PoS: Postcard For: Folio Horizontal o2r: Oficio II CPF: 11" × 15" Horizontal InP: Irregular Size YYY × XXX (") Y-direction: 3. 88 - 11. 33" X-direction: 5. 88 - 17" [Metric specifications] b6r: B6 Horizontal* A6r: A6 Horizontal Pos: Postcard Ldr: Ledger Horizontal LGr: Legal Horizontal Ltr: Letter Horizontal LtE: Letter Vertical Str: Statement Horizontal o2r: Oficio II CPF: 11" × 15" Horizontal InP: Irregular Size YYY × XXX (mm) Y-direction: 98 - 297mm X-direction: 148 - 432mm 1 - 250 (*250) on: Rotate oFF: No Rotation* Reference Page 6-23 F24 F25 Copy Limit 2-Sided Copy Reverse-side Rotation Setting Margin Shift Limits the number of copies or sets of copies that can be made at one time. Rotates the paper 180 degrees and copies it when both sides of a sheet are to be copied. * This will not be displayed when the optional Duplex Unit is not installed. Sets the initial value for the Binding Margin. 6-24 6-24 F26 [Inch specifications] 0. 13/0. 25/0. 38/0. 50/0. 63/0. 75 (") (*0. 25) [Metric specifications] 1 - 18 (mm) (*6) [Inch specifications] 0. 13/0. 25/0. 38/0. 50/0. 63/0. 75 (") (*0. 25) [Metric specifications] 1 - 18 (mm) (*6) 6-25 F27 Border Width Sets the initial value for the border width that will be lightened to remove shadows from the sheet or book. 6-26 F28 4 in 1 Layout Setting Sets the layout for the order in which the originals will appear in the 4-in-1 Layout mode. 6-26 1-: 12 34 1 3 2 4 2-: 13 24 1 2 3 4 3-: (*1-) 4-: 6-9 Section 6 COPIER MANAGEMENT Display Items F29 Settings Items Merge Copy Borderline Rotate Sort Setting Description Selects the type of borderline to be used in the Layout mode. Sets the copier so that each copy set is rotated and sorted when it is sort-copied. Shortens the amount of time the internal motor continues to run after the copy is produced. Use this setting in cases when the motor noise is bothersome. Sets the copier so that automatic clearing is executed after a set amount of time has elapsed after the copy is produced. (Refer to P. 2-4 "Regarding the Auto-clear function". ) Available settings 1-: No Borderline* 2-: Solid Line 3-: Dotted Line on: Rotational Sorting Enabled oFF: Rotational Sorting Disabled* 0, 5, 10, 15, 30 (seconds) (*10) Reference Page 6-27 F30 6-28 F31 Silent Mode Transition Time Auto Clear Setting 6-28 F32 on: Enabled* oFF: Disabled 6-29 F33 Auto Off Setting The Auto Off mode will be entered after a set period of on: Enabled* time has passed after the final copy has been produced oFF: Disabled or during which no operations have been performed. If the Auto Off function interferes with your copy operations, disable the function. Before disabling the Auto Off function, you may want to try lengthening the amount of time before the Auto Off function engages (Off Mode Transition Time). Sets the time interval prior to the automatic operation of the Auto Clear function when on (Enable) has been selected as the Auto Clear setting. * This will not be displayed when F32 is set to "oFF". Sets the time interval prior to the automatic engagement of the Low Power mode after copy operations have been completed. Sets the time interval prior to the automatic operation of the Auto Clear function when on (Enable) has been selected as the Auto Clear setting. * This will not be displayed when F33 is set to "oFF". The Alarm can be set to sound when a key on the Operation Panel is pressed or in cases when errors occur, etc. 10 - 270 (10-second units) (*90) 6-29 F34 Auto Clear Time 6-30 F35 Low Power Mode Transition Time Off Mode Transition Time 1, 5, 15, 30, 45, 60, 90, 120, 180, 240 (minutes) (*15) 1, 5, 15, 30, 45, 60, 90, 120, 180, 240 (minutes) (*30) 6-31 F36 6-31 F37 Alarm on: Enabled (sound alarm) oFF: Disabled (no alarm)* 6-32 F38 Toner Coverage Report Prints out a report that shows the number of copies --made and the average amount of toner used (blackness ratio %) for each paper size. 6-33 6-10 Section 6 COPIER MANAGEMENT Default Settings Mode Operations Procedures Follow the procedure listed below to operate in the [Default Settings Mode]. 4 Press the [Enter] key. Inch specifications Metric specifications 1 Depress the [Exposure Adjustment] keys on both sides for 3 seconds. "F00 (Default Settings Mode)" will be displayed in the No. of Copies display. Procedure for Changing the Default Settings The procedure for changing each of the items in the Default Settings is described below. [. . . ] 6-25 Merge Copy Borderline (Default Settings) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-27 Mixed Original Sizes (Auto Selection) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Multi-bypass tray Paper Size (Default Settings) . . . . . . . . . . . . . . . . . . . . . . . 6-22 Multi-bypass tray Size Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]