User manual OLYMPUS CAMEDIA C-2100 ULTRA ZOOM

[. . . ] DIGITAL CAMERA C-2100 Ultra Zoom INSTRUCTIONS 1 GETTING STARTED 2 BASIC FUNCTIONS 3 SHOOTING FOR SPECIAL SITUATIONS 4 USING YOUR CAMERA'S ADVANCED FUNCTIONS 5 ADVANCED RECORDING/ DISPLAY TECHNIQUES 6 PRINT SETTINGS 7 TRANSFERRING PICTURES TO A COMPUTER 8 MISCELLANEOUS Before using your camera, read this manual carefully to ensure correct use. We recommend that you take test shots to get accustomed to your camera before taking important photographs. Thank you for purchasing an Olympus digital camera. Before you start to use your new camera, please read these instructions carefully to enjoy optimum performance and a longer service life. Keep this manual in a safe place for future reference. Legal and other notices ·All contents of this publication are subject to change without notice. [. . . ] Use this mode when backlight is making the subject darker. 1 Press or metering) until (Spot (Center-weighted averaging metering) mark is displayed on the control panel. 1 2 2 Take pictures. Note: When MULTI METERING is set to ON, ESP is not available. 132) When the Mode dial is set to M, the metering mode can be switched. However, the exposure setting value is adjusted in the Manual mode (P. The exposure value is displayed on the bar. Control panel Metering mark 100 Changing the ISO Increase the ISO when you want to take pictures in low-light situations with a fairly high shutter speed. You can select from AUTO, as well as 100, 200 and 400. When you set to AUTO, the sensitivity is automatically changed depending on the shooting conditions. The higher the ISO, the faster the shutter speed that can be used and the less light required. 2, 3 1 Menu appears. Press . pad to select to select the 3 Press sensitivity, then press the OK button. You can select AUTO only when the Mode dial is set to P, SPrg, . To go back to the normal screen, press the OK button again. ISO appears on the control panel when a setting other than AUTO is selected. ISO blinks on the control panel even when the ISO is automatically increased in the AUTO mode. 1 P F2. 8 1/800 0. 0 AUTO DIGITAL ZOOM WB ISO 100 200 400 [1/5] Menu (still picture recording mode) Control panel ISO mark Note: The ISO scale is based on that used for conventional photographic film, but the figures are for reference only. When set to AUTO, sensitivity will be changed to 100 when the Mode dial is set to A/S/M. When AUTO is selected, the ISO is automatically increased in low-light situations when the flash is not used. This is to prevent blurring from camera shake. Pictures will appear grainy when the ISO is high. Unless OFF is selected in All Reset, the setting will be canceled and reset to AUTO when the power is turned off (p. 148). 101 RECORDING--brightness/exposure (Cont. ) Recording images sequentially with different exposures -- Auto bracket Use this mode to record images with different exposures. Focus and white balance will be measured first and fixed during sequential shooting. You can select the number of pictures to take sequentially. Control panel 1 Set the record mode to any mode other than TIFF. If the record mode is set to TIFF, available. 2 Press on 3 Press BKT, then the Arrow pad to select press . Recording mode 3, 4, 5 4 Press then press to select the range, . to select the number 5 Press of pictures, then press the OK button repeatedly until the Menu disappears. 2 P F2. 8 1/800 0. 0 0. 3 SLOW P F2. 8 1/800 0. 0 0. 3 BKT MULTI METERING 0. 6 1. 0 x3 x5 SLOW BKT MULTI METERING 0. 6 1. 0 x3 x5 [2/5] [2/5] 102 6 Press from theuntil panel. [. . . ] CARD ERROR Cannot record, play back or erase pictures in this card. If you are taking pictures, remove the write-protect adhesive seal. If the card is dirty, wipe it with a clean tissue and insert it again. If the problem is still not corrected, this card cannot be used. Load the image using personal computer image processing software. [. . . ]