User manual OLYMPUS D-230

[. . . ] DIGITAL CAMERA C-2 D-230 REFERENCE MANUAL «Click Here» CAMERA OPERATION CONNECTING THE CAMERA TO A PC QUICK START GUIDE DIGITAL CAMERA C-2 D-230 OPERATION MANUAL CAMERA OPERATION G Thank you for purchasing an Olympus digital camera. G Please read this manual carefully before using your camera. We recommend that you become familiar with your camera by taking a number of test shots before performing important shooting. INTRODUCTION This manual explains the correct operating procedures for your camera. Read it carefully and keep it in a safe place for future reference. ABOUT THIS MANUAL G The information contained in this manual may be subject to change without notice. [. . . ] When formatting a previously used card, check each image before formatting to avoid accidentally erasing image you want to keep. Once a card is formatted, images previously stored on that card can not be restored. · Do not open the card cover or remove the batteries during formatting as this may cause a card malfunction. · A card with a write protect seal attached can not be formatted. Do not reuse the removed write protect seal. Caution 73 OTHER FUNCTIONS REC VIEW After each picture is taken, the image is displayed on the LCD monitor for a few seconds for you to view. 1 2 3 4 5 OTHER FUNCTIONS Open the lens barrier. The camera turns on in the Record mode. Press the button. The monitor shows the Camera menu. Select [SETUP] using the buttons and press the button. Select [REC VIEW] using the / buttons and press the button. Select [ON] using the buttons and press the button. ON: The monitor briefly shows the last image you took once shooting is completed. / / OFF:The camera is ready to take the next picture immediately after shooting is completed. Press the button again to exit the menu. Note The Rec view mode remains when the lens barrier is closed. 74 CLEAR SETTINGS You can choose to keep the shooting-related settings, such as the flash mode and image quality settings, as they are for the next picture or return to the default settings when the camera is turned off. If you do not want to change the settings to suit the weather or subject, select [HOLD] to keep current settings. This conveniently avoids having to re-enter settings each time the camera is used (as would be the case if the settings are cleared). For details of the settings, see "Clear settings value" ( p. 76). 1 2 3 4 5 Open the lens barrier. The camera turns on in the Record mode. Press the menu. button. The monitor shows the Camera Select [SETUP] using the buttons and press the button. Select [ ] using the / buttons and press the button. Select [HOLD] using the buttons and press the button. By selecting [HOLD], you can keep the current settings. Press the menu. / / OTHER FUNCTIONS button again to exit the Note The clear settings remains when the lens barrier is closed. 75 CLEAR SETTINGS CLEAR SETTINGS VALUE [RESET] When the camera is turned off, the shooting-related settings are deleted and the camera reverts to the defaults (default settings). The settings remain, even if the camera is turned off. [HOLD] Settings when [RESET] or [HOLD] is selected and the camera is turned on Settings for the Record mode Digital tele Exposure compensation Flash Drive Focus Metering White balance Image quality Sharpness Contrast LCD monitor (for the Record mode) Settings for the Play mode Image information Settings for other functions Rec view OTHER FUNCTIONS [RESET] Default Default Default Default Default Default Default Default Default Default Default [RESET] Default [RESET] Keep Keep Keep Keep [HOLD] Keep Keep Keep Keep Keep Keep Keep Keep Keep Keep Keep [HOLD] Keep [HOLD] Keep Keep Keep Keep Default Refer to Off (1. 0×) 0. 0 Auto Single Auto ESP Auto HQ Normal Normal Off Default p. 35 p. 36 p. 30 p. 38, 40, 57 p. 33, 42 p. 43 p. 44 p. 46, 59 p. 48 p. 50 p. 20 Refer to Off Default p. 77 Refer to Off On 9 ±0 p. 74 p. 71 p. 52 p. 78 Beep tone Index playback Monitor brightness 76 DISPLAYING IMAGE INFORMATION This function enables you to display or not to display the image information on the monitor while the image is played back. If you select [ON], the information is displayed for 3 seconds. displayed, see "Monitor indications" ( Image information display ON Image information display OFF 1 2 3 4 5 Close the lens barrier and press the button. The camera turns on in the Play mode. Press the button. The monitor shows the Play menu. Select [PLAY] using the buttons and press the button. / Select [INFO] using the / buttons and press the button. Select [ON] using the buttons and press the button. / OTHER FUNCTIONS The image information is displayed on the image. Press the button again to exit the menu. Note · The image information display setting returns to [OFF] (default setting) when the clear settings value is [RESET] and the p. 75). See "Clear settings" ( · Only , and are displayed after 3 seconds, regardless of whether image information display setting is set to [ON] or [OFF]. 77 MONITOR BRIGHTNESS If the monitor is hard to see, you can adjust it to suit the surrounding brightness. 1 2 3 4 5 OTHER FUNCTIONS Close the lens barrier and press the button. The camera turns on in the Play mode. Press the button. The monitor shows the Play menu. Select [SETUP] using the buttons and press the button. Select [ ] using the / buttons and press the button. [. . . ] Press the I IMAGE QUALITY (SHQ, HQ, SQ1, SQ2) 1 2 3 4 5 6 Press the button with the lens barrier open to display the Camera menu. Select [PICTURE] using the / buttons and press the button. ] using the / buttons and press the button. Select [ / buttons and press the button. [. . . ]