User manual OLYMPUS IZOOM 75

[. . . ] INSTRUCTIONS Read this manual carefully before using your camera. Indicates circumstances under which mishandling resulting from ignoring this symbol could result in personal injury or property damage. KEEP THE BATTERIES AWAY FROM FIRE. NEVER TRY TO DISASSEMBLE, RECHARGE, OR SHORT-CIRCUIT BATTERIES. 2 NEVER ATTEMPT TO DISASSEMBLE THE CAMERA; IT CONTAINS A HIGH-VOLTAGE CIRCUIT. IF THE INTERNAL PARTS OF THE CAMERA ARE EXPOSED DUE TO DROPPING OR DAMAGE, REMOVE THE BATTERIES IMMEDIATELY TO PREVENT FURTHER USAGE. IN CASE OF MALFUNCTION, CONSULT YOUR NEAREST OLYMPUS DEALER OR OLYMPUS SERVICE CENTER. 3 Names of parts . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the selftimer/remote control button to display . To cancel this mode, press the selftimer/remote contrtol button again. This mode is canceled automatically when not used for more than 10 minutes. 2. Aim the remote control at the camera, and press the button. The shutter will be released after about 3 seconds. 48 WARNINGS: · KEEP THE REMOTE CONTROL OUT THE REACH OF CHILDREN. IF A CHILD SWALLOWS THE REMOTE CONTROL, CONTACT A DOCTOR IMMEDIATELY. · NEVER EXPOSE THE REMOTE CONTROL TO EXCESSIVE HEAT OR OPEN FLAME. Notes: · Use the remote control within a range that can be seen in the viewfinder. · The camera will focus on the subject directly in front of it. · The remote control may not work when the subject is backlit. · The remote control may not work when there is inverted fluorescent light near the camera. 49 Attaching to the Strap Open the buckle , insert the strap , and close the buckle The remote control can be . attached to round straps with a diameter of 3 mm ~ 5 rnm (0. 12 ~ 0. 2 in) and flat straps with a thickness of 1. 2 mm ~ 2 mm (0. 05 ~ 0. 08 in) and a width of 6 mm ~ 12. 5 mm (0. 23 ~ 0. 42 in). 50 Replacing the Battery 1. Open the buckle and remove the battery cover inside by sliding in the direction of the arrow. 2. Insert a new battery (CR1220) with the plus mark showing on top . Attach the battery cover by sliding in the direction of the arrow 4. Close the buckle . Handling Cautions · Never apply excessive force to the remote control when attached to the strap. · Usable temperature range: -10°C ~ 40°C (14°F ~ 104°F). 51 CORRECTING THE DATA 1. Press the MODE button for two seconds or longer. The year indication will start blinking. 2. Press the SET button to correct the year. If you press the button once, the number on the display will advance by 1. And if you keep it pressed, the numbers will run in rapid succession. 52 3. Press the MODE button again. The month indication will start blinking. 4. Repeat steps 2 and 3 to set the day, hour and minutes. button, the blinking indication changes in the order of year, data correction will be finished again. month, day, hour, and minute. The when the MODE button is pressed Note: As you press the mode 53 PRINTING THE DATE AND TIME Choose the desired mode. The mode will switch in the described order. pressed, the display will change in the sequence shown below. · The quartzdate function uses the same power source as the main unit. Be sure to correct the data after the battery is replaced. · The printing of dates is handled differently by different processors. [. . . ] Degree of protection indicated by second characteristics numeral 4. Short description -- Protected against splashing water. Definition -- Water splashed against enclosure from any direction shall have no harmful effect. 76 SPECIFICATIONS FOR DATE UNIT Data recording method: Recording using magnetic IX (information input) function. Data coding: No data, year-month- day, month-day-year, daymonth-year and hour-minute. External indication of data: Data display on LCD panel Film speed setting: Automatic film speed setting. [. . . ]