User manual OLYMPUS PT-048

[. . . ] PT-048 µ TOUGH-8010/STYLUS TOUGH-8010/µ TOUGH-6020/STYLUS TOUGH-6020 µ TOUGH-8010/STYLUS TOUGH-8010/µ TOUGH-6020/STYLUS TOUGH-6020 µ TOUGH-8010/STYLUS TOUGH-8010/µ TOUGH-6020/STYLUS TOUGH-6020 µ TOUGH-8010/STYLUS TOUGH-8010/µ TOUGH-6020/STYLUS TOUGH-6020 µ TOUGH-8010/STYLUS TOUGH-8010/µ TOUGH-6020/STYLUS TOUGH-6020 µ TOUGH-8010/STYLUS TOUGH-8010/µ TOUGH-6020/STYLUS TOUGH-6020 µ TOUGH-8010/STYLUS TOUGH-8010/µ TOUGH-6020/STYLUS TOUGH-6020 En Thank you for buying the Underwater Case PT-048 (hereinafter Case). Please read this instruction manual carefully and use the product safely and correctly. Please keep this instruction manual for reference after reading it. Wrong use may cause damage to the camera inside the Case due to water leakage, and repair may not be possible. [. . . ] Preparations Check the contents of the package. En Check that all accessories are in the box. Contact your dealer if accessories are missing or damaged. · LCD hood (on the body) · Silicone grease · Optical fiber cable adapter · Silica gel (1g) · LCD hood strap · Lens cap · Hand strap · Case body (Check that the O-ring is installed) · O-ring remover · Adapter Black (PTAC-07) White (PTAC-06) · Instruction manual (this manual) · OLYMPUS distributor list EN 8 Names of the parts 3 4 5 En 2 1 6 7 8 9 ba 0 1 2 *3 *4 Palm grip Diffuser Shutter lever ON/OFF button 5 6 7 8 Accessory mount Front lid Open/close dial Lens ring 9 0 a b LCD inner hood O-ring Tripod seat Light shield hood EN 9 c d e f En g h i m *c *d *e *f *g *h Arrow pad ( (REC) button Zoom buttons q button INFO button/arrow pad Arrow pad lk j *j E button k button/arrow pad l MENU button m LCD monitor window *i OK/AFL button (*1) (*1) During Underwater WideAngle 1 or Underwater Macro shooting mode, the OK button functions as the AF LOCK button. Memo: The Case operation parts marked by * corresponds to the operation parts of the digital camera. When the operation parts of the Case are operated, the corresponding functions of the digital camera will operate. For details of the functions, refer to the instruction manual for the digital camera. EN 10 Using the accesories Install the strap Install the strap on the Case body. Installation illustration Installation completed En Hand strap Hand strap ring How to use the hand strap Pass your hand through the hand strap and adjust the length with the stop button. stop button EN 11 Installation and removal of the LCD hood Installation Strongly push the LCD hood as shown in the figure into the rails above and below the LCD monitor window. Removal Remove the LCD hood from the rails above and below the LCD monitor window by widening the LCD hood. En Guides Installation Removal Mounting and removing the lens cap Fit the lens cap onto the lens ring as shown in the figure. Be sure to remove the lens cap before shooting. EN 12 Using the fiber cable adapter The fiber cable adapter is required when connecting the separately available UFL-1 underwater flash to the Case using an underwater optical fiber cable (optional: PTCB-E02). Before diving, make sure that you have enough remaining battery power. 2. Confirmation of the Remaining Number of Pictures to be Taken Confirm that the image storage has a sufficient remaining number of pictures to be taken. 3. Remove the hand strap from the digital camera. When a digital camera is loaded without removing the strap, the strap may get caught between the Case lids and may cause water leakage. 4. Attach the adapter to the digital camera. Attach the digital camera while distending the adapter slightly. White adapter (PTAC-06) for µ TOUGH-6020/STYLUS TOUGH-6020. Black adapter (PTAC-07) for µ TOUGH-8010/STYLUS TOUGH-8010. CAUTION: When combination of the digital camera and the adapter is incorrect, the camera does not operate correctly. Be sure to check the combination while installing the digital camera. EN 15 Open the Case 1 Slide and hold the slide lock towards the arrow direction (1 of figure below) and turn the open/close dial counter clockwise (2 of figure below). 2 Turn the open/close dial to the position where it cannot be turned further. 3 Open the rear lid of the Case gently. En 1 Slide lock 2 Open Open/close dial CAUTION: Do not exert too much force while turning the open/close dial. Doing so may damage the dial. EN 16 Load the digital camera 1 Confirm that the digital camera is OFF. 2 Gently insert the digital camera which has attached the adapter into the Case. 3 Insert 2 piling up silica gel bags (1g) between the bottom of the digital camera and the Case. The silica gel bag provided for prevention of fogging. 2 En 3 CAUTION: · The silica gel bag will be caught when the Case is sealed and water leakage will occur. · Once silica gel has been used, the moisture absorption performance will be impaired. Always replace the silica gel when the Case is opened and closed. Make sure the camera is loaded properly Check the following points before sealing the Case. · Is the digital camera loaded properly? [. . . ] · When a sharp object is used to remove the O-ring or to clean the inside of the O-ring groove, the Case and the O-ring may be damaged and water leakage may occur. · Take care not to stretch the O-ring. · Never use alcohol, thinner, benzene or similar solvents or chemical detergents to clean the O-ring. When such chemicals are used, the O-ring may be damaged or its deterioration will be accelerated. EN 25 How to Apply Grease to the O-ring Apply the exclusive lubricant to each O-ring. [. . . ]