User manual OMRON 3G3MV-P10CDT3-E

[. . . ] I01E-EN-01 USER'S MANUAL Programmable Controller Option Board Models 3G3MV-P10CDT-E and 3G3MV-P10CDT3-E (For SYSDRIVE 3G3MV Multi-function Compact Inverters) 3G3MV-P10CDT PLC Option Unit User's Manual Revised June 2003 Notice: OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. Always consult the information provided with them. Failure to heed precautions can result in injury to people or damage to the product. DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. [. . . ] When using the peripheral port disconnect any devices connected to the RS422/485 port. Communications switch Switch to select port 1 type of connected device Position Communication port 1 OFF (default) ON 7. Programming Console RS-422/485 communication RS-422/485 port (3G3MV-P10CDT3-E only) Used to connect to host computers, or standard external devices. Terminal Arrangement Receive data (input) Send data (output) RDA- RDB+ Shield SDA- SDB+ Connector: Phoenix MSTB 2. 5/5-STF-5. 08AU Note The maximum line length is 500 m. Note The peripheral port and RS-422/485 port cannot be used simultaneously. When using the peripheral port disconnect any devices connected to the RS422/485 port. RS-422/485 switch (3G3MV-P10CDT3-E only) Switch to select 4-wire (RS-422) or 2-wire (RS-485) communication Position Status OFF (down) (default) ON (up) 9. 4-wire communications 2-wire communications Terminating Resistance switch (3G3MV-P10CDT3-E only) Position Termination OFF (down) (default) Disabled ON (up) Enabled Set this switch to ON only for double-ended connection to a Host Link network. I/O connector Connects the CPU Unit to external input and output devices. Sinking outputs COM (-) IN0 (A) IN1 (B) IN2 (Z) OUT0 OUT1 OUT2 OUT3 1 2 COM COM 1 2 3 4 5 6 7 8 9 10 11 12 Connector: WAGO 733-112 (wire cross section 0. 08 to 0. 50 mm ) 28 COM 2 IN3 IN4 IN5 Unit Components and Specifications 11. Relay connector SECTION 2 Connects the CPU Unit to an external output devices. Connector: WAGO 734-102 (wire cross section 0. 08 to 1. 50 mm2) 12. FE-connection AMP tab to connect functional earth. Internally connected to pin 3 of the RS422/485 connector and to the shell of the peripheral connector. Enabled 13. Low battery detection switch (3G3MV-P10CDT3-E only) This switch enables or disables the detection of a low-battery error. Position Low-battery detection Error detection enabled Error detection disabled Disabled OFF ON (up) (default) OFF (down) 29 SECTION 3 Installation and Wiring This section provides information on installing and wiring a 3G3MV-P10CDT Unit. Be sure to follow the directions and precautions in this section when installing the 3G3MV-P10CDT in a panel or cabinet and wiring I/O. 3-1 3-2 3-3 3-4 3-5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Connecting I/O Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Wiring Communication Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Programming Device Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 31 Installation and Wiring SECTION 3 3-1 Installation WARNING Do not touch the conductive parts such as internal PCBs or terminal blocks WARNING while power is being supplied. Doing so may result in electrical shock. Turn ON the input power supply only after mounting the front cover, terminal covers, bottom cover, Operator, and optional items. Leave them mounted in place while power is being supplied. Not doing so may result in electrical shock, malfunction, or damage to the product. Wiring, maintenance, or inspection must be performed by authorized personnel. Not doing so may result in electrical shock or fire. [. . . ] SetPoint of position (in units) DM10 and DM11 SP_PV_Scale_N1 : Numerator of SP&PV scaling SP_PV_Scale_N2 : Denominator of SP&PV scaling Scaling is . . units 2. 03 BIT (R/W) 0 2. 04 3. 00 3. 01 BIT (R/W) BIT (R) BIT (R) 0 --- 3. 02 3. 03 BIT (R) BIT (R) --- DM10 DM12 DM14 DWORD (R/W) BCD DWORD (R/W) BCD DWORD (R/W) BCD 0 1 1 N1 = quads N2 2 Default values correspond to direct quad control DM16 DWORD (R/W) BCD DWORD (R/W) BCD DWORD (R/W) BCD DWORD (R/W) Decimal DWORD (R/W) BCD In_Position1_Window : Defines the width of the In_Position output 1. This has to be the most accurate positioning window. In units In_Position2_Window : Defines a wider window for use in the software sequence (start some actions just while the movement is being finished). [. . . ]