User manual OMRON CJ2H-CPU65-EIP DATASHEET

[. . . ] SYSMAC CJ-series CJ2H (Built-in EtherNet/IP) CPU Units CJ2H-CPU6@-EIP CSM_CJ2H-CPU-EIP_DS_E_2_1 Flagship PLCs with Built-in Multifunctional Ethernet Port · Small, Fast, Flexible: The CJ2 CPU Units inherit and improve CJ1 features while also adding EtherNet/IP as a standard feature for high-speed, high-capacity Ethernet-based networking. CJ2H-CPU6@-EIP Features · · · · · High-speed, high-capacity EtherNet/IP is built into every model. The CIP communications protocol is supported for direct access to multivendor devices. Tag memory provided for easy access from host PCs and PTs. Even more program memory and data memory. [. . . ] The specified I/O memory data can be stored in the trace memory in the CPU Unit. · The trace data can be uploaded during data tracing using CX-Programmer, which enables continuously logging the data by constantly uploading the trace data (trace data uploading during tracing). · Data tracing can be automatically started when operation is started (i. e. , when the operating mode is changed from PROGRAM mode to MONITOR or RUN mode). The location and task number where execution stopped for a program error is recorded. The programs can be checked for items such as no END instruction and FALS/FAL errors at startup. Clock Function Operation Start Time Storage Operation Stop Time Storage Clock Startup Time Storage Power Interruption Time Storage Total Power ON Time Calculation Power ON Clock Data Storage User Program Overwritten Time Storage Parameter Date Storage Memory Protection Power Supply Management Power OFF Detection Time Setting Power OFF Detection Delay Time Number of Power Interruptions Counter Function Blocks Languages in Function Block Definitions Online Editing Force-Set/Reset Differentiate Monitoring Debugging Data Tracing Storing Location of Error when an Error Occurs Program Check 8 CJ2H-CPU6@-EIP Function Error Log CPU Error Detection User-defined Failure Diagnosis Selfdiagnosis and Restoration Load OFF Function RUN Output Basic I/O Load Short-circuit Detection Failure Point Detection CPU Standby Detection Description A function is provided to store predefined error codes in CPU Unit, error information, and time at which the error occurred. Errors can be generated for user-specified conditions: Non-fatal errors (FAL) and fatal errors (FALS). Program section time diagnosis and program section logic diagnosis are supported (FPD instruction). This function turns OFF all outputs from Output Units when an error occurs. The RUN output from the CJ1W-PA205R turns ON while CPU Unit is in RUN mode or MONITOR mode. This function provides alarm information from Basic I/O Units that have load short-circuit protection. The time and logic of an instruction block can be analyzes using the FPD instruction. This function indicates when the CPU Unit is on standby because all Special I/O Units and CPU Bus Units have not been recognized at the startup in RUN or MONITOR mode. System FAL Error Detection This function generates a non-fatal (FAL) error when the user-defined conditions are met in (User-defined non-fatal error) program. Duplicate Refreshing Error Detection Backup Memory Error Detection PLC Setup Error Detection Non-fatal Error Detection CPU Bus Unit Error Detection Special I/O Unit Error Detection Tag Memory Error Detection Battery Error Detection CPU Bus Unit Setting Error Detection Special I/O Unit Setting Error Detection Memory Error Detection Selfdiagnosis and Restoration (Continued from previous page) I/O Bus Error Detection Unit/Rack Number Duplication Error Too Many I/O Points Error Detection I/O Setting Error Detection Program Error Detection Instruction Processing Error Detection Fatal Error Detection Indirect DM/EM BCD Error Detection Illegal Area Access Error Detection No END Error Detection Task Error Detection Differentiation Overflow Error Detection Invalid Instruction Error Detection User Program Area Overflow Error Detection Cycle Time Exceeded Error Detection This function detects an error when an immediate refreshing Instruction in an interrupt task is competing with I/O refreshing of a cyclic task. This function detects errors in the memory backup of the user programs and parameter area (backup memory). This function detects setting errors in the PLC Setup. This function detects an error when there is an error in data exchange between the CPU Unit and a CPU Bus Unit. This function detects an error when there is an error in data exchange between the CPU Unit and a Special I/O Unit. This function detects errors in tag memory. This function detects an error when a battery is not connected to the CPU Unit or when the battery voltage drops. This function detects an error when the model of a CPU Bus Unit in the registered I/O tables does not agree with the model that is actually mounted in the PLC. This function detects an error when the model of a Special I/O Unit in the registered I/O tables does not agree with the model of Unit that is actually mounted. This function detects errors that occur in memory of the CPU Unit. [. . . ] For communications commands addressed to Special I/O Units or CPU Bus Units, refer to the operation manual for the related Unit. W446 W447 CX-Programmer Operation Manual WS02-CX-V@ CX-Programmer Operation Manual Functions Blocks CX-Programmer Operation Manual SFC Programming CXONE-ALD-V@ CS/CJ/CP/NSJ-series CX-Integrator Network Configuration Software Operation Manual CX-One Setup Manual Support Software for Windows computers CX-Programmer operating procedure Describes operating procedures for the CX-Programmer. Also refer to the Software User's Manual (W473) and Instructions Reference Manual (W474) when you do programming. W469 W464 Network setup and monitoring Describes the operating procedures for the CX-Integrator. W463 Installing software from the CX- Provides an overview of the CX-One FA Integrated Tool One Package and describes the installation procedure. 14 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. [. . . ]