User manual OMRON CX-ONE V1.1 SETUP MANUAL 11-2005

[. . . ] 1. 1 FA Integrated Tool Package SETUP MANUAL CXONE-AL1. 1 FA Integrated Tool Package Setup Manual Revised November 2005 iv Notice: OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. Always heed the information provided with them. [. . . ] ) DeviceNet DeviceNet Unit (CS1W/CJ1W-DRM) CX-Protocol Serial Communications Start with Settings Board/Unit Inherited (CS1W-SCB) Start with Settings Inherited Start with Settings Inherited Select CX-Integrator. NS-series PC (-V1) Start with Settings Inherited CX-Designer CX-Position Position Control Unit (CS1W/CJ1W-NC@) Position Control Unit with MECHATROLINK-II Communications (CJ1W-NCF Temperature Controller Start with Settings Inherited CX-Thermo CX-Motion-NCF Start with Settings Inherited Start with Settings Inherited CX-Motion CompoWay/F CX-Process Tool Start with Settings Inherited Loop Control Unit/Board (CS1W-LC001/LCBP) Faceplate AutoBuilder for NS Start with Settings Inherited CX-Profibus PROFIBUS-DP Master Unit (CJ1W-PRM) CX-FLnet Start with Settings FL-net Unit Inherited (CS1W/CJ1W-FLN) Select Tools - Network Settings. Select Tools - Start Routing Table from the menu bar or right-click Network Communications Unit in Online Connection Information Window and select Start Routing Table from the pop-up menu. Select Tools - Start Data Link from the menu bar or right-click Controller Link or SYSMAC LINK Unit in Online Connection Information Window and select Start Data Link from the pop-up menu. Routing Table Component Switch Box Utility Select Tools - Switch Box Utility. Data Link Component 7 System Requirements Starting while Inheriting Settings Section 1-4 · Setting the device type is not required every time different Support Software is started. · The online connection is also inherited by the newly opened Support Software. · New project files are automatically created for the newly opened Support Software. Starting with or without Inheriting Settings If Open - Save As is selected after starting Support Software, the save to folder will be the same as the one used with the CX-Programmer. 1-4 1-4-1 System Requirements System Requirements The system requirements for the CX-One are given in the following table. Item Requirement Operating system (OS) Microsoft Windows Microsoft Windows Microsoft Windows Microsoft Windows (See note 1. ) 98SE NT (Service Pack 6a) 2000 (Service Pack 3 XP Japanese or English sysor higher) or Microsoft tem Windows Me Computer IBM PC/AT or compatible with a Pentium II 333 MHz or faster processor (Pentium III 1 GHz or faster recommended. ) Memory Hard disk Display Disk drive Communications ports Other 256 MB minimum (See note 2. ) Approx. 1. 8 GB or more available space is required to install the complete CX-One package. SVGA (800 × 600) or better high-resolution display with 256 colors min. (See note 3. ) Internet access is required for online user registration, including a modem or other hardware connection method. Note (1) CX-One Operating System Precaution The CX-One will not run on Microsoft Windows 95 or any other OS not listed above. If such an OS is being used on the client computer, the OS must be upgraded before installing the CX-One. System requirements and hard disk space may vary with the system environment. (2) The amount of memory required varies with the Support Software used in CX-One. Refer to user documentation for individual Support Software for details. (3) An RS-232C port is required to connect the Support Software in CX-One to a PLC. If the computer provides only a USB port, use a CS1W-CIF31 USB-to-RS-232C Conversion Cable. For connecting to the CP Series, however, an over-the-counter USB cable (type A-B) can be used. 8 System Requirements Section 1-4 1-4-2 Hard Disk Space Requirements for Support Software in CX-One Support Software in CX-One CX-Programmer CX-Integrator CX-Position CX-Motion CX-Motion-NCF CX-Motion-MCH CX-Drive CX-Designer CX-Process Tool Faceplate Auto-Builder for NS CX-Protocol CX-Profibus CX-Simulator CX-Thermo CX-FLnet Switch Box CX-Server and PLC Tools Approx. Remarks Options can be selected or cleared to install or not install individual Support Software. Note If the complete CX-One package is installed, approximately 1. 8 GB of hard disk space will be required (including workspace required for installation). [. . . ] Note (1) Do not uninstall the CX-Server if there are other programs on the computer that use it as the communications driver, e. g. , the CX-Programmer. If the CX-Server is uninstalled, it will no longer be possible to use these other programs. (2) Do not uninstall the CX-Server while other programs that use it as the communications driver are running on the computer, e. g. , the CX-Programmer. The CX-Server may not uninstall properly if other programs are using it. [. . . ]