User manual OMRON CX-POSITION V2.5 06-2008

[. . . ] 2. 5 Operation Manual Revised June 2008 iv Notice: OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. Always heed the information provided with them. Failure to heed precautions can result in injury to people or damage to property. !DANGER !WARNING Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. [. . . ] Press the Enter Key, or use the Up or Down Keys, to set the setting. Settings can be displayed in either hexadecimal or decimal format. (Refer to 4-2-3 Switching Setting Display Formats. ) 2. When the Setting Editing Window is active, the left-hand side of its status bar will display the possible range for entries. Possible range for entries is displayed Press the Backspace Key before setting an entry to alter it. Note If entering settings directly, decimal values must be entered starting with the leading zero (i. e. , 0. ). To Move the Cursor To Move the Window Move the cursor in individual Setting Editing Windows either by using the Cursor Keys or by clicking in the window directly. Settings that cannot be displayed in a single window can be viewed either by pressing the PageDown Key or by using the scroll bar on the right-hand side of the window. 57 Setting Editing Windows Section 4-2 4-2-3 Switching Setting Display Formats Settings in any Setting Editing Window can be displayed in either hexadecimal or decimal format. Switching the Current Settings Display Format Switch the display format by selecting Hexadecimal or Decimal under View Change Display in the Setting Editing Window or by right-clicking and selecting Hexadecimal or Decimal from the pop-up menu. Example: The following windows will be displayed for speed settings in hexadecimal (right) and decimal (left) formats Decimal Notation Hexadecimal Notation Switching the Settings Display Format on Startup Set the display format when starting up CX-Position by selecting Tools Options - Default Display Format. To switch to hexadecimal display, select the Hexadecimal Display option. 4-2-4 Clearing Settings Set parameter settings can be made into default settings and non-parameter setting ranges can be cleared. To Clear to Default Settings 1, 2, 3. . . Use the following procedure to clear axis settings to their default values. With the Parameter Setting Editing Window enabled, either select Edit Defaults Clear, or right-click and select Defaults Clear from the pop-up menu. 2. Select the axis for which settings are to be cleared to the defaults. A dialog box will be displayed asking if the settings should be returned to their default values. Click the OK Button. 58 Setting Editing Windows To Clear Setting Ranges 1, 2, 3. . . Non-parameter settings can also be cleared. Section 4-2 1. In the (non-parameter) editing window, select the settings to be cleared, or designate the range by clicking and dragging. 2. Select Edit - Clear, or right-click and select Clear from the pop-up menu. Note Under the Edit Menu, Default Clear is enabled when parameter settings are selected, and Clear is enabled when non-parameter settings are active. 4-2-5 Copying Axis Settings For 2-axis and 4-axis Position Control Units, data can be copied from one axis to another axis by selecting the source and destination axes. Applicable Position Control Units Settings That Can Be Copied 4-axis NCs: CS1W-NC413/NC433 and CJ1W-NC413/NC433 2-axis NCs: CS1W-NC213/NC233 and CJ1W-NC213/NC233 The following settings can all be copied using a single procedure. · Parameters · Sequences · Speeds · Accelerations/Decelerations · Dwell Times · Zones 1, 2, 3. . . Under From, select the axis to be copied from. The default settings are from X axis to Y axis. 59 Editing Parameter Settings The From axis cannot be the same as the To axis. Section 4-3 For 4-axis Position Control Units, if the same axis is clicked for the To axis as the one already selected for the From axis, the next To axis will be selected automatically (in the order Y, Z, U, X). More than one axis can be selected for the To axis (except for the axis already selected as the From axis). For 2-axis Position Control Units, selecting the Y axis as the From axis will automatically make the X axis the To axis, and vice-versa. Change the To axis by click and selecting a different axis. [. . . ] Page 67: Information added before 5-2-2. Page 70: "Programming Console" changed to "PLC Setup. " Page 71: Section reference information changed in middle of page. Page 72: Section reference information changed at top of page. Page 80: Information added at bottom of page. [. . . ]