User manual OMRON E3X-DA-N DATASHEET

[. . . ] Digital Fiber Amplifier E3X-DA-N Time Incident level Stable detection Time E3X-DA-N Truly ultimate fiber amplifier in pursuit of "user friendliness" and "high performance" UL991* * UL-listed including UL991 tests/evaluations Applicable standard: UL3121-1 Standards for additional tests/evaluations for applications: UL991, SEMI S2-0200 Features Reducing power line wiring meaning space is saved. New design for easier Industry First Patent pending maintenance. The connector type that uses the wire-saving connector supplies power to the single-conductor slave connectors via the three-conductor master connector. Hence, the following three has been made possible. Relay connectors are not required meaning that space is used more efficiently and costs are reduced. [. . . ] Use to select SET, ADJ, or RUN mode. Operation Indicator (orange) Channel-selection Switc ON when output is ON. Mode Selector Use to select SET, ADJ, or RUN mode. E3X-DA-N A-429 E3X-DA-N Repeated accuracy vs. sensing distance Reflective model E32-DC200 Operation General 1 Changing the Display (RUN Mode) 2 Zero-reset (RUN Mode) Set the mode selector to RUN . RUN Digital incident level (4000 max. ) Set the mode selector to RUN . RUN Digital incident level (4000 max. ) (Factory-set to RUN) TEACH MODE 2s * To reset to zero again: TEACH 1s 1s Digital Percent To return the initial digital incident level: TEACH MODE Hold down both for 3 s. Note: There is no limit on the number of times zero-reset can be used. MODE 2s Analog incident level and threshold 3 Initial Reset (SET Mode) Set the mode selector to SET . SET MODE 2s TEACH MODE @ Manual Tuning (Fine Sensitivity Adjustment) in ADJ Mode Perform fine sensitivity adjustment after teaching and manual tuning (without using the teaching function) in the way shown below: Twin-output Models Select the channel to be adjusted using the channel selection switch. CH1 CH2 Hold down both for 5 s. TEACH MODE MODE Cancel Fine sensitivity adjustment TEACH MODE Execute initial reset Set the mode selector to ADJ . ADJ Sensitivity increment with threshold decrement Sensitivity decrement with threshold increment The items displayed in ADJ mode vary with the display setting in RUN mode. RUN mode Digital incident level Digital percent Analog value ADJ mode Digital threshold Digital Percent Analog value A-430 Advanced Photoelectric Sensors 4 Setting Functions in SET Mode Set the mode selector to SET . SET TEACH Digital incident level display There are four different sensitivity settings. Refer to page AB- for details. MODE 2s Sensing function Displayed as "F". Monitor Focus Standard (factory-set) TEACH Available with: E3X-DA21-N E3X-DA51-N E3X-DA7 E3X-DA9 (B) Super-long distance TEACH (A) MODE 2s Super-high speed TEACH MODE Setting upper Alternates between limit for monitoring "A-UP" and setting value. (Factory setting) Alternates 2s Timer function 0 (Factory-set) Displayed as "t". TEACH In units of 100 from 4, 000 Alternates TEACH Adjustable in 1-ms units for 0 to 20 ms and in 5-ms units for higher. TEACH 200 TEACH Alternates MODE 2s Flashing setting OFF (factory-set) Displayed as "L". TEACH Alternates TEACH TEACH ON TEACH MODE MODE Note: It is not possible to set an upper limit that is lower than the lower limit. 2s Hold setting OFF (factory-set) Displayed as "H". Setting lower Alternates between limit for monitoring "A-LO" and setting value. (Factory setting) TEACH Alternates TEACH Peak TEACH In units of 100 from 0 Alternates Bottom TEACH MODE TEACH Alternates 2s Display orientation setting Reversing display TEACH Standard (factory-set) TEACH TEACH Alternates Reverse (B) (A) TEACH Note: It is not possible to set an lower limit that is lower than the upper limit. E3X-DA-N A-431 E3X-DA-N Twin-output models 4 Setting Functions in SET Mode Set the mode selector to SET . SET TEACH Digital incident level display There are four different sensitivity settings. Refer to page AB- for details. (B) Setting the operating mode Changing the operating mode (A) The operating mode for the channel set with the channel-selection switch can be changed. Changed using the channel-selection switch CH1 CH2 MODE 2s Timer function 0 (Factory-set) Displayed as "t". Channel 1 Channel 2 TEACH Adjustable in 1-ms units for 0 to 20 ms and in 5-ms units for higher. L ON (Factory setting) TEACH L ON (Factory setting) TEACH MODE 200 TEACH 2s D ON D ON Flashing setting OFF (Factory-set) Displayed as "L". MODE 2s Sensing function Displayed as "F". ON TEACH Standard (factory-set) TEACH MODE TEACH 2s Hold setting OFF (Factory-set) Displayed as "H". Super-long distance TEACH TEACH Super-high speed TEACH Peak TEACH Area TEACH (B) (A) MODE Bottom TEACH @ Area Sensing Area sensing is possible using the threshold values for channels 1 and 2. · If channel 1 is set to L/ON, output turns ON when the incident level is between the thresholds. · If channel 1 is set to D/ON, output turns OFF when the incident level is between the thresholds. The result is output to control output 1. (Control output 2 is always OFF. ) 2s Display orientation setting Reversing display Standard (Factory-set) TEACH Reverse TEACH A-432 Advanced Photoelectric Sensors General E3X-DA-N When teaching is performed (SET mode) · The four types of teaching given below are available. · Once setting is made, operation is performed in the preset status thereafter. When a teaching error occurs, the level indicators flash in red. Restart setting from the beginning. Twin-output models only Select the channel to be adjusted using the channel selection switch. CH1 Set the mode selector to SET CH2 . SET Maximum Sensitivity Setting Procedure Two-point With/Without-object Teaching Operation Procedure SET Operation Set the mode selector to SET. SET 1 2 Set the mode selector to SET. Press the TEACH button for 3 seconds min. Setting is completed when the red-lit level indicators turn to green. Then they return to the digital incident level display. Set to RUN mode. 1 TEACH 3s (red) 2 With the work present, press the SET button once (about 1 s). Object 3 TEACH 1s (green) 3 The level indicators are lit red. (red) 4 RUN One-point without-object teaching Procedure Operation Set the mode selector to SET. SET 4 If no work is pending, press the SET button once (about 1 s). TEACH 1 1s 5 2 Press the SET button once (about 1 s). TEACH 6 1s Setting is completed when the green indicators are turned ON. Then they return to the digital incident level display. Set to RUN mode. (green) RUN Note: With and without work may be in any order. 3 Setting is completed when the red level indicators are turned ON. [. . . ] Before installing an end plate, remove the clip from the master amplifier unit using a nipper or similar tool. Dimensions (Unit: mm) Amplifier Units prewired E3X-DA11-N E3X-DAH11-N E3X-DA41-N E3X-DAH41-N E3X-DAG11-N E3X-DA21-N E3X-DAB11-N E3X-DAB41-N E3X-DAG41-N E3X-DA51-N E3X-DA11D With Mounting Blanket Attached 17. 15 13. 05 44. 9 x 3 = 14. 7 Incident level display Threshold level display (A) * 1 *2 3 Two, 2. 4 dia. 10 Operation Indicator 64. 3 38. 6 5. 3 Mounting Holes 8 31. 5 9. 9 2-M3 10. 7 4. 1 22. 4 13 Two, 3. 2 dia. holes 3. 4 16 34. 8 Hole for optical communications 10. 75 16 2. 4 4 * 1. The Mounting Bracket can also be used on side A. [. . . ]