User manual OMRON E3Z-G DATASHEET

[. . . ] Grooved-type Photoelectric Sensor I Grooved design eliminates the need for optical E3Z-G axis adjustment. I Two-axis models also available. [. . . ] 1 E3Z-G61-M3J E3Z-G81-M3J E3Z-G62 E3Z-G82 Through beam (grooved type) 2 E3Z-G62-M3J E3Z-G82-M3J Item Sensing distance Light source (wave length) Power supply voltage Current consumption Control output PNP output 25 mm (distance between arms of groove) Circuit protection Response time 1 E3Z-G Sensing method Number of optical axes NPN output Item PNP output Ambient illumination (receiver side) Ambient temperature Ambient humidity Insulation resistance Dielectric strength Vibration resistance (destruction) Shock resistance (destruction) Enclosure rating Connection method Indicator Weight (packed state) Material Accessories E3Z-G61 E3Z-G81 1 E3Z-G61-M3J E3Z-G81-M3J E3Z-G62 E3Z-G82 Through beam (grooved type) 2 E3Z-G E3Z-G62-M3J E3Z-G82-M3J Incandescent lamp: 3, 000 lux max. Operating: - to 55°C/Storage: - to 70°C (with no icing or condensation) 25 40 Operating: 35% to 85%/Storage: 35% to 95% (with no condensation) 20 M min. at 500 VDC between lead wires and case 1, 000 VAC, 50/60 Hz for 1 min between lead wires and case 10 to 55 Hz, 1. 5-mm double amplitude for 2 hours each in X, Y, and Z directions 500 m/s2 3 times each in X, Y, and Z directions IP64 (IEC60529) Pre-wired cable Junction connector (length: 2 m or 0. 5 m) Operation indicator (orange) Pre-wired models (with 2-m cable): 65 g Models with junction connectors: 30 g ABS Instruction sheet Pre-wired cable Junction connector (length: 2 m or 0. 5 m) Operation I Output Circuits (NPN Output) Output transistor status Light ON Timing chart Mode selector Output circuit No. of optical axes/model 1 axis E3Z-G61 E3Z-G61M3J Incident Interrupted Operation ON indicator (orange) OFF ON Output transistor OFF Operate Load (relay) Reset (Between brown and black) LIGHT ON (L/ON) Operation indicator (orange) 1 Brown Load (relay) 12 to 24 VDC 100 mA max. (Control output) Black Main circuit 4 (S1) ZD 3 Blue 0V Dark ON Incident Interrupted Operation ON indicator OFF (orange) ON Output transistor OFF Operate Load (relay) Reset (Between brown and black) DARK ON (D/ON) Connecting Pin Arrangement 2 1 4 3 Note: Pin 2 is not used. 2 axes E3Z-G62 E3Z-G62M3J Light ON Incident Interrupted Operation ON indicator OFF (orange) ON Output transistor OFF Operate Load (relay) Reset (Between brown and black) LIGHT ON (L/ON) Operation indicator S1 (orange) 1 Operation indicator S2 (orange) Brown 100 mA max. 12 to 24 VDC Load (relay) (Control output) ZD (S1) Main circuit 4 Black 100 mA max. (Control output) 2 White (S2) Load (relay) Dark ON Incident Interrupted Operation ON indicator OFF (orange) Output transistor Load (relay) ON OFF Operate Reset (Between brown and black) DARK ON (D/ON) ZD 3 Blue 0V Connector Pin Arrangement 2 1 4 3 2 E3Z-G I E3Z-G Output Circuits (PNP Output) Output transistor status Light ON Timing chart Mode selector Output circuit No. of optical axes/model 1 axis E3Z-G81 E3Z-G81M3J Incident Interrupted Operation ON indicator (orange) OFF Output transistor Load (relay) ON OFF Operate Reset (Between brown and black) LIGHT ON (L/ON) Operation indicator (orange) (Control output) Main circuit ZD 1 Brown 12 to 24 VDC 4 Black (S1) 100 mA max. 3 Blue Load (relay) 0V Dark ON Incident Interrupted Operation ON indicator OFF (orange) ON Output transistor OFF Operate Load (relay) Reset (Between brown and black) DARK ON (D/ON) Connector Pin Arrangement 2 1 4 3 Note: Pin 2 is not used. 2 axes E3Z-G82 E3Z-G82M3J Light ON Incident Interrupted Operation ON indicator OFF (orange) ON Output transistor OFF Load (relay) Operate Reset (Between brown and black) LIGHT ON (L/ON) 1 Operation indicator S2 (orange) Brown 12 to 24 VDC Operation indicator S1 (orange) (Control output) 4 Black (S1) Main circuit ZD (Control output) 2 White (S2) Dark ON Incident Interrupted Operation ON indicator OFF (orange) ON Output transistor OFF Operate Load (relay) Reset (Between brown and black) DARK ON (D/ON) ZD 3 Blue 100 mA max. Load (relay) 100 mA max. Load (relay) 0V Connector Pin Arrangement 2 1 4 3 Structure of Sensor I/O Connector Wire color 4 3 2 1 1 2 3 4 Brown White Blue Black XS3F-M421-402-A XS3F-M421-405-A XS3F-M422-402-A XS3F-M422-405-A Classification Wire color Connector pin number 1 2 3 4 Use 1-axis models Power supply (+V) --Output Output 2 (S2) Output 1 (S1) Power supply (0 V) 2-axis models DC Brown White Blue Black Note: Pin 2 of 1-axis models is not used. 3 E3Z-G E3Z-G Dimensions Optical axis S1 (see note) Optical axis S2 (see note) 50 35 Two, 4. 5 dia. Junction Connector Models (E3Z-G6(-M3J) Mode selector 4-dia. , 4-core vinyl-insulated round cable Standard length: 0. 3 m 40 25 7. 5 S1 S2 20 36 40 4-dia. , 4-core vinyl-insulated round cable (Conductor cross-section: 0. 2 mm2; insulator diameter: 1. 1 mm) Standard lengths: 2 m, 0. 5 m 11 M8 9 19 2 1 4 3 Note: Both 1 and 2-axis models have S1; only 2-axis models have S2. S1 output: black S2 output: white Operation indicator (orange) ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0. 03937. [. . . ] Shiokoji Horikawa, Shimogyo-ku Kyoto, 600-8530 Japan Tel: (81)75-344-7068/Fax: (81)75-344-7107 Printed in Japan 0501-1M (A) 4 [. . . ]