User manual OMRON E5ZN

[. . . ] H113-E1-03B E5ZN Temperature Controller OPERATION MANUAL E5ZN Temperature Controller Operation Manual Revised November 2005 Notice: OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. Always heed the information provided with them. Failure to heed precautions can result in injury to people or damage to property. !DANGER !WARNING !Caution Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. [. . . ] The command is successfully executed. 89 Variable Area Map Section 5-10 5-10 Variable Area Map The variable area of the Temperature Controller is mapped in terms of variable types and addresses as described below. Variable type C0: Read-only data for setting area 0, including PVs and status Variable type C1: Setting data for setting area 0 Variable type C3: Setting data for setting area 1 Variable type C5: Setting data for setting area 0 Variable type C7: Setting data for setting area 1 Allocations for each variable are listed below. A dash (-) in the "ch" column indicates data that is used by both channels. This data is used by pulse output models only. This data is used by analog output models only. This data is used by upgraded pulse output models and analog output models only. Monitor value PV Description Temperature: According to specified range for each sensor. Analog: Scaling lower limit - 5% FS to scaling upper limit + 5% FS 0001 0002 0003 0004 0005 0006 Status Internal SP Heater current value monitor Refer to page 91. Lower limit of SP to upper limit of SP 00000000H to 00000226H (0. 0 to 55. 0) (See note 1. ) Variable Address type C0 0000 ch 1 MV monitor for heating Standard: FFFFFFCEH to 0000041AH (-5. 0 to 105. 0) Heating/cooling: 00000000H to 0000041AH (0. 0 to 105. 0) MV monitor for cooling 00000000H to 0000041AH (0. 0 to 105. 0) PV hold value Temperature: According to specified range for each sensor Analog: Scaling lower limit - 5% FS to scaling upper limit + 5% FS Value stored in internal non-volatile memory (RAM) when the "PV hold" operation command was executed. Temperature: According to specified range for each sensor Analog: Scaling lower limit - 5% FS to scaling upper limit 5% + FS 0100 2 PV 0101 0102 0103 0104 0105 0106 Status Internal SP Refer to page 91. Lower limit of SP to upper limit of SP Heater current value 00000000H to 00000226H (0. 0 to 55. 0) (See note 1. ) monitor MV monitor for heating Standard: FFFFFFCEH to 0000041AH (-5. 0 to 105. 0) Heating/cooling: 00000000H to 0000041AH (0. 0 to 105. 0) MV monitor for cooling 00000000H to 0000041AH (0. 0 to 105. 0) PV hold value Temperature: According to specified range for each sensor Analog: Scaling lower limit - 5% FS to scaling upper limit + 5% FS Value stored in internal non-volatile memory (RAM) when the "PV hold" operation command was executed. 90 Variable Area Map 15 14 13 12 11 10 9 0 0 8 7 0 6 5 4 0 3 0 2 0 1 0 Bit position Section 5-10 Status Value of bit 0 Refresh Not detected Not detected OFF OFF OFF OFF OFF OFF Hold Detected Detected ON ON ON ON ON ON 1 Detected Current exceeded Not detected Current hold Indicate range exceeded. Input error Heating output (See note. ) Cooling output (See note. ) HB output Alarm output 1 Alarm output 2 Alarm output 3 Note: For pulse output models, the status of these bits shows the status of the corresponding operation indicators. For analog output modes, the status of these bits is undefined (i. e. , the bits will not necessarily show the status of the indicators). 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 00000 000 Bit position Status Event input Write mode EEPROM (See note. ) Value of bit 0 OFF Backup RAM = EEPROM 1 ON RAM write RAM EEPROM Setting area Setting area 0 Setting area 1 AT executing STOP Enable Manual AT execute/cancel AT canceled RUN/STOP Data writing Auto/manual RUN Disable Automatic Note: EEPROM is the internal non-volatile memory. 91 Variable Area Map Section 5-10 Variable Address ch type C1 0000 - Setting data name Operation/adjustment protection 00000000H (0): 00000001H (1): 00000002H (2): 00000003H (3): Description No restriction at the operation/adjustment levels Moving to adjustment level is disabled. Only "PV" and "PV/SP" display and change enabled. Only "PV" and "PV/SP" display enabled. Moving to initial level/communications setting level enabled and moving to advanced function setting level displayed. Moving to initial level/communications setting level enabled and moving to advanced function setting level not displayed. Moving to initial setting/communications setting levels is disabled. OFF (Setting changes using the E5ZN-SDL enabled. ) ON (Setting changes using the E5ZN-SDL disabled. ) 0001 Initial setting/communica- 00000000H (0): tions protection 00000001H (1): 00000002H (2): 0002 Setting change protection 00000000H (0): 00000001H (1): 0003 0004 0005 0006 0007 0008 0009 000A 000B 000C 000D 000E 000F 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 1 SP Alarm value 1 Alarm upper limit value 1 Alarm lower limit value 1 Alarm value 2 Alarm upper limit value 2 Alarm lower limit value 2 Alarm value 3 Manual manipulated value Heater burnout detection SP 0 SP 1 Temperature input offset value Upper limit temperature input offset value Lower limit temperature input offset value Proportional band Integral time Derivative time Cooling coefficient Dead band Manual reset value Heating hysteresis Cooling hysteresis Lower limit of SP to upper limit of SP FFFFF831H to 0000270FH (-1, 999 to 9, 999 or -199. 9 to 999. 9) FFFFF831H to 0000270FH (-1, 999 to 9, 999 or -199. 9 to 999. 9) FFFFF831H to 0000270FH (-1, 999 to 9, 999 or -199. 9 to 999. 9) FFFFF831H to 0000270FH (-1, 999 to 9, 999 or -199. 9 to 999. 9) FFFFF831H to 0000270FH (-1, 999 to 9, 999 or -199. 9 to 999. 9) FFFFF831H to 0000270FH (-1, 999 to 9, 999 or -199. 9 to 999. 9) FFFFF831H to 0000270FH (-1, 999 to 9, 999 or -199. 9 to 999. 9) Standard: FFFFFFCEH to 0000041AH (-5. 0 to 105. 0) Heating/cooling: FFFFFBE6H to 0000041AH (-105. 0 to 105. 0) 00000000H to 000001F4H (0. 0 to 50. 0) (See note 1. ) Lower limit of SP to upper limit of SP Lower limit of SP to upper limit of SP FFFFF831H to 0000270FH (-199. 9 to 999. 9) FFFFF831H to 0000270FH (-199. 9 to 999. 9) FFFFF831H to 0000270FH (-199. 9 to 999. 9) 00000001H to 0000270FH (0. 1 to 999. 9) 00000000H to 00000F9FH (0 to 3999) 00000000H to 00000F9FH (0 to 3999) 00000001H to 0000270FH (0. 01 to 99. 99) FFFFF831H to 0000270FH (-199. 9 to 999. 9) 00000000H to 000003E8H (0. 0 to 100. 0) 00000000H to 0000270FH (0. 1 to 999. 9) 00000000H to 0000270FH (0. 1 to 999. 9) 92 Variable Area Map Variable Address ch type C1 0100 Setting data name Operation/adjustment protection 00000000H (0): 00000001H (1): 00000002H (2): 00000003H (3): 0101 Initial setting/communica- 00000000H (0): tions protection 00000001H (1): Description Section 5-10 No restriction at the operation/adjustment levels Moving to adjustment level is disabled. Only "PV" and "PV/SP" display and change enabled. Only "PV" and "PV/SP" display enabled. Moving to initial level/communications setting level enabled and moving to advanced function setting level displayed. Moving to initial level/communications setting level enabled and moving to advanced function setting level not displayed. [. . . ] Pages 71, 72, 74, and 75: Corrected addresses for variable type C3. Pages 76, 77, and 81: Changed command tables. Page 82: Added new section 5-9-19 and changed response table. Pages 85 and 87 through 95: Changed tables. [. . . ]