User manual OMRON F160-2 MANUAL 2

[. . . ] Z171-E1-01A F160-2 Vision Sensor Manual 2: CONVERSATIONAL MENU OPERATION MANUAL READ AND UNDERSTAND THIS DOCUMENT Please read and understand this document before using the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. [. . . ] (The stored reference images are not cleared. ) If No is Selected, go to 4-1-2 Re-registering Reference Images. 4-1-2 Re-registering Reference Images Select Yes to update the reference images. The reference images will be registered using the same procedure as the first time. 0. Scn 0 =SET= Ref image The previous reference image has not been cleared. Yes No Back SeeAlso CHECK Refer to page 22 STEP 2: Registering Reference Images. If you want to keep the previous reference image, select No. When the Power Has Been Turned OFF After Previous Inspection Conditions Were Set The reference images will have been cleared. Either place a workpiece of the same size in the same position and register that image or, if the reference image was backed up to a computer or Memory Card, download the image as memory image 35. (Refer to page 81 and page 85. ) If you have downloaded backed up images, select STEP as the image storage method and select memory image 35. (Refer to page 22. ) CHECK 4-1-3 Changing Setting Details 1. Select Add. STEP 3 Add the region using the same procedure as STEP 3: Selecting and Setting Inspection Types. Adding Regions 67 Changing and Clearing Inspection Conditions 1. Select Add. 0. Scn 0 =SET= Region Change what? Start Ref image >>Region Position End Section 4-1 Add Delete Change region End Back S+:Switch display Use the same procedure as STEP 3: Selecting and Setting Inspection Types to add the region. Changing the Position or Size of Regions 1. Select Channge region. 2. Select region to change. 3. Change position or size. 1. Select Change region. 0. Scn 0 =SET= Region Change what? Start Ref image >>Region Position End Add Delete Change region End Back S+:Switch display In this explanation, Presence/Size will be used as an example. The Select Region to Change Screen will be displayed. 0. Scn 0 =SET= Region Select region to change. 0. Presence(Shape ) :Region ENT:Select ESC:Back 2. Select the number of the region to be changed. ENT Key: Sets the selection. 68 Changing and Clearing Inspection Conditions Section 4-1 The screen for changing the position and size of the region will be displayed. 0. Scn 0 =SET= Region 86, 98 0. Presence(Shape ) Enclose the area to be inspected. : Move ENT:Set ESC: Back SeeAlso 3. Refer to page 18 for details on drawing figures. The screen in step (2. ) will return. Deleting Regions 1. Select Delete. 2. Select region. 3. Delete region. 1. Select Delete. 0. Scn 0 =SET= Region Change what? Start Ref image >>Region Position End Add Delete Change region End Back S+:Switch display The Select Region To Delete Screen will be displayed. 0. Scn 0 =SET= Region Select region to delete. 0. Presence(Shape ) :Region ENT:Select ESC:Back 2. Select the region to delete. ENT Key: Sets the selection. 69 Changing and Clearing Inspection Conditions A confirmation message will be displayed. The region will be deleted. Yes No Back Section 4-1 3. Select Yes to delete the region. If other regions are set, the screen in step (1. ) will return. 0. Scn 0 =SET= Region Select the type of Start inspection. Ref image (Up to 32 regions) >>Region Position Presence End Orient'n Conform Position Chip/Bur Back Dimens'n Surface S+ENT:Help S+:Switch display If the deleted region was the only region, the screen for selecting inspection types will return. 4-1-4 Changing Position Displacement Compensation 1. Change settings?Yes When Position Compensation Is Set 2. Change regions for position compensation. 3. Specify movement range. 4. No Delete Exit settings. When Position Compensation Is Not Set Perform the operations outlined under STEP 4: Inconsistent Workpiece Positions. Select Yes to change the position compensation settings. Change position compensation?Yes No Delete Back Select No to not change the settings. [. . . ] cuted? Why has the measurement time increased after switching from the Expert Menu to the Conversational Menus, even though no settings have been changed? 126 Appendix A Menus Scn SET P. 63 Up to 32 regions can be set. Region P. 28 Presence Conform Orient'n Position Dimns'n Chip/Bur Position P. 102 Communications Output device Display settings P. [. . . ]