User manual OMRON F250-C50 C55 SETUP 09-2001

[. . . ] ) 9LVLRQ 6HQVRU )&& 0DQXDO 6HWXS 0DQXDO 3URGXFHG 6HSWHPEHU iv Notice: OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. Always heed the information provided with them. Failure to heed precautions can result in injury to people or damage to property. !DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. !WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. !Caution Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or property damage. OMRON Product References All OMRON products are capitalized in this manual. [. . . ] Applications: Surface inspections, positioning, and hole inspections of comparatively small objects Camera Half mirror Light source Measurement object 26 Memory Cards Section 3-3 3-3 Memory Cards Use a Memory Card to back up data such as settings and image data or increase the number of scenes when you are using the Scene Group function. Data from the F250 can be backed up in the computer just by inserting the Memory Card into the computer and copying the desired data. The following procedures also apply to the Memory Card containing the F250-UME Application Software. We recommend the OMRON F160-N64S (64 MB). CHECK The F250 is equipped with two Memory Card slots. Use these slots for the following functions. Function F250-UME Application Software installation Memory Cards for scene groups Memory Cards for data backup Slot number Slot 0 (Use slot 0 only. ) Slot 1 (Use slot 1 only. ) Either slot 0 or 1 can be used. Precaution A filler card with no memory is inserted into the F250's Memory Card slot before the F250 is shipped. Remove this filler card and install a Memory Card to use the Memory Card functions. If Memory Cards are not being used, leave the filler card in place to prevent dust or dirt from entering the Memory Card slot. 3-3-1 Installing a Memory Card 1. Insert the Memory Card into the Memory Card slot. CHECK The eject button will pop out slightly when the Memory Card is inserted properly. 3-3-2 Removing the Memory Card 1. Turn OFF the power supply to the Memory Card or turn OFF the F250. Refer to Section 4 Additional Functions in the F250 Vision Sensor Manual 2: Operation Manual for details on turning OFF the power supply to the Memory Card. Verify that the Memory Card indicator is not lit. Memory card indicator SeeAlso 27 Memory Cards Precaution 3. Section 3-3 Do not remove the Memory Card if the Memory Card indicator is lit. Doing so may damage the Memory Card or the F250 itself. Press the eject button to the right of the Memory Card slot. The Memory Card will pop out slightly. Precaution Do not remove the Memory Card without pressing the eject button. Doing so may damage the F250. Memory card eject button 4. Pull the Memory Card straight out from the slot. 3-3-3 Using Memory Cards in a Personal Computer The F250's Memory Cards can be used in a personal computer with a PC Card drive (PCMCIA 2. 0 or higher, type II compatible) or CompactFlashTM drive. The Memory Card must be inserted into a PC Card Adapter in order to be used in a PC Card drive. We recommend the OMRON HMC-AP001 PC Card Adapter. PC Card Adapter 28 SECTION 4 Connecting External Devices This section describes how to connect external devices through a parallel interface (a parallel connector) or serial interface (the RS-232C/RS-422 connector or Ethernet connector). 4-1 Connecting through the Parallel Interface . 4-1-1 4-1-2 4-1-3 Parallel Connection Methods . . 30 30 32 36 37 37 40 4-2 Connecting through the Serial Interface . 4-2-1 4-2-2 29 Connecting through the Parallel Interface Section 4-1 4-1 Connecting through the Parallel Interface This section explains how to connect I/O to the F250 through its parallel interface to input signals such as measurement triggers or output signals such as measurement results. When you want to use the parallel interface to input commands and output measurement results, prepare a parallel I/O cable and connect it to the parallel connector. A Terminal Block can also be used to connect external devices. [. . . ] 170 g 61 Specifications F150-VS Camera Cable (For F150-S@, F160-S@ Cameras) 3000 Section 5-4 Unit: mm 51 36 (30) 20 dia. 43 6 dia. 14. 7 dia. 15 dia. F250 Connector Signal Power GND GND VIDEO GND VD ESCNT1 VIDEO HD SCAN ESCNT2 INDEX TRG Shell Connector model: Hirose RP17A-13PA-12PC Pin 1 2 3 4 5 6 7 8 9 10 11 12 Camera Connector Pin 1 2 3 4 5 6 7 8 9 10 11 12 Signal GND Power GND VIDEO VIDEO GND HD Not used. ESCNT1 ESCNT2 INDEX TRG SCAN Shell Connector model: Hirose HR10A-10P-12S 62 Specifications Cameras) 3000 (120) Section 5-4 F160-VSR3 Camera Cable (For F300-S2R/S3DR/S4R and F200-S@ Unit: mm 5. 3 dia. 46 15 dia. 43 14. 7 dia. F250 Connector Signal Power GND GND VIDEO GND VD ESCNT1 VIDEO HD SCAN ESCNT2 INDEX TRG Shell Connector model: Hirose RP17A-13P-12PC Pin 1 2 3 4 5 6 7 8 9 10 11 12 Camera Connector Pin 1 2 3 4 5 6 7 8 9 10 11 12 Signal GND Power VIDEO GND VIDEO HD GND HD VD GND - INDEX(SI) TRG VD GND Shell Connector model: Hirose HR10A-10P-12S 63 Specifications F160-VSR4 Camera Cable (For F300-S Cameras) 3000 (120) Section 5-4 Unit: mm 5. 3 dia. 46 15 dia. 17. 4 dia. 43 14. 7 dia. F250 Connector Signal Power GND GND VIDEO GND VD ESCNT1 VIDEO HD SCAN ESCNT2 INDEX TRG Shell Connector model: Hirose RP17A-13P-12PC Pin 1 2 3 4 5 6 7 8 9 10 11 12 Camera Connector Pin 1 2 3 4 5 6 7 8 9 10 11 12 Signal GND Power VIDEO GND VIDEO HD GND HD VD GND - INDEX(SI) Power VD GND Shell Connector model: Hirose HR10A-10P-12S F150-VM Monitor Cable 2000 Unit: mm 46. 7 11. 5 dia. 3. 3 dia. 46. 7 Item Vibration resistance Shock resistance Ambient temperature Ambient humidity Ambient environment Materials Specification 10 to 150 Hz; half-amplitude: 0. 15 mm, 4 times for 8 minutes each in 3 directions 196 m/s2, 3 times each in 6 directions Operating: 0 to 50 C (with no condensation) Storage: -25 to 65 C (with no condensation) 35% to 85% (with no condensation) No corrosive gases Cable sheathing: Heat-resistant chlorinated vinyl Connector: PVC 64 Specifications Item Minimum bending radius Weight Accessories 50 mm Approx. [. . . ]