User manual OMRON F3S-B

[. . . ] E502-E2-01 F3S-B Series Safety Light Curtain Instruction Manual F3S-B Introduction Thank you for purchasing the F3S-B series Safety Light Curtain. Always heed the following points when using the F3S-B: · · · Make sure that personnel operating the F3S-B are knowledgeable about the machine on which it is installed Read this manual completely and be sure you understand the information provided before attempting to operate the F3S-B Keep the manual in a secure and convenient location and refer to it as necessary. Regulations and Standards (1) The F3S-B has not received the type approval provided by Article 44-2 of the Industrial Safety and Health Law of Japan. Therefore, it cannot be used in Japan as a safety device for pressing or shearing machines provided by article 42 of that law. [. . . ] Only with F3S-B P and BM P. 1-8 Indicators <Emitter Indicators> Optical-axis line mark <Receiver Indicators> POWER INTERLOCK EXT. TEST/ BLANKING IR-power indicator (Orange) Interlock indicator (Yellow) External test / blanking indicator (Green) ON OFF UNSTAB ON-state indicator (Green) OFF-state indicator (Red) Instability indicator (Orange) Emitter IR-power indicator Interlock indicator External test/ blanking indicator ON-state indicator OFF-state indicator Instability indicator Receiver : Lit when emitting. : Lit during start/restart interlock and start interlock. / Flashing when using blanking function. Flashing during connection with F39-E1 or with failure. : Lit with an insufficient light reception or failure. Flashing during connection with F39-E1. 13 F3S-B 1-9 Table of Types Type Naming Rule F3S - B M 36 2 P 12 - L blank $ Stand-alone M $ Master unit for series connection S $ Slave unit for series connection 36 2 5 7 $ No. of optical axis (4-66) $ 25mm optical pitch $ 50mm optical pitch $ 75mm optical pitch blank $ Slave unit P $ PNP outputs blank $ Stand-alone or slave unit 12 $ No. of optical axis of the connected slave unit for 25mm optical pitch type : 12, 18, 24, or 30 for 50mm optical pitch type : 06, 09, 12, or 15 for 75mm optical pitch type : 04, 06, 08, or 10 blank $ Complete set of emitter and receiver L $ Emitter unit only D $ Receiver unit only Stand-alone Master unit Slave unit Optical resolution 30 mm No. of optical axes 12 18 24 30 36 42 48 54 60 66 6 9 12 15 18 21 24 27 30 33 4 6 8 10 12 14 16 18 20 22 Protective height 300 mm 450 mm 600 mm 750 mm 900 mm 1, 050 mm 1, 200 mm 1, 350 mm 1, 500 mm 1, 650 mm 300 mm 450 mm 600 mm 750 mm 900 mm 1, 050 mm 1, 200 mm 1, 350 mm 1, 500 mm 1, 650 mm 300 mm 450 mm 600 mm 750 mm 900 mm 1, 050 mm 1, 200 mm 1, 350 mm 1, 500 mm 1, 650 mm Weight (without accessories) 0. 9 kg 1. 2 kg 1. 5 kg 1. 8 kg 2. 1 kg 2. 5 kg 2. 8 kg 3. 1 kg 3. 4 kg 3. 7 kg 0. 9 kg 1. 2 kg 1. 5 kg 1. 8 kg 2. 1 kg 2. 5 kg 2. 8 kg 3. 1 kg 3. 4 kg 3. 7 kg 0. 9 kg 1. 2 kg 1. 5 kg 1. 8 kg 2. 1 kg 2. 5 kg 2. 8 kg 3. 1 kg 3. 4 kg 3. 7 kg F3S-B122P F3S-B182P F3S-B242P F3S-B302P F3S-B362P F3S-B422P F3S-B482P F3S-B542P F3S-B602P F3S-B662P F3S-B065P F3S-B095P F3S-B125P F3S-B155P F3S-B185P F3S-B215P F3S-B245P F3S-B275P F3S-B305P F3S-B335P F3S-B047P F3S-B067P F3S-B087P F3S-B107P F3S-B127P F3S-B147P F3S-B167P F3S-B187P F3S-B207P F3S-B227P 14 F3S-BM122P F3S-BM182P F3S-BM242P F3S-BM302P F3S-BM362P F3S-BM422P F3S-BM482P F3S-BM542P F3S-BM602P F3S-BM662P F3S-BM065P F3S-BM095P F3S-BM125P F3S-BM155P F3S-BM185P F3S-BM215P F3S-BM245P F3S-BM275P F3S-BM305P F3S-BM335P F3S-BM047P F3S-BM067P F3S-BM087P F3S-BM107P F3S-BM127P F3S-BM147P F3S-BM167P F3S-BM187P F3S-BM207P F3S-BM227P F3S-BS122 F3S-BS182 F3S-BS242 F3S-BS302 F3S-BS065 F3S-BS095 F3S-BS125 F3S-BS155 55 mm F3S-BS047 F3S-BS067 F3S-BS087 F3S-BS107 80 mm F3S-B 1-10 Table of Response Time 1-10-1 Stand-alone type Response time [ms ] Response time [ms ] Response time [ms ] F3S-B122P F3S-B182P F3S-B242P F3S-B302P F3S-B362P F3S-B422P F3S-B482P F3S-B542P F3S-B602P F3S-B662P 20 20 20 23 27 30 34 37 41 45 F3S-B065P F3S-B095P F3S-B125P F3S-B155P F3S-B185P F3S-B215P F3S-B245P F3S-B275P F3S-B305P F3S-B335P 20 20 20 20 20 21 22 24 26 28 F3S-B047P F3S-B067P F3S-B087P F3S-B107P F3S-B127P F3S-B147P F3S-B167P F3S-B187P F3S-B207P F3S-B227P 20 20 20 20 20 20 20 20 20 21 1-10-2 Series connection types The following chart shows the response time of combinations of a master unit and a slave unit connected in series. For example, the response time of the combination of F3S-BM122P30 and F3S-BS302 is 30 ms. Response time [ms] Slave unit Master unit F3S-BM122P F3S-BM182P F3S-BM242P F3S-BM302P F3S-BM362P F3S-BM422P F3S-BM482P F3S-BM542P F3S-BM602P F3S-BM662P Slave unit Master unit F3S-BM065P F3S-BM095P F3S-BM125P F3S-BM155P F3S-BM185P F3S-BM215P F3S-BM245P F3S-BM275P F3S-BM305P F3S-BM335P Slave unit Master unit F3S-BM047P F3S-BM067P F3S-BM087P F3S-BM107P F3S-BM127P F3S-BM147P F3S-BM167P F3S-BM187P F3S-BM207P F3S-BM227P F3S-BS122 F3S-BS182 F3S-BS242 F3S-BS302 20 23 27 30 34 37 41 45 49 54 23 27 30 34 37 41 45 49 54 57 27 30 34 37 41 45 49 54 57 61 30 34 37 41 45 49 54 57 61 65 F3S-BS065 F3S-BS095 F3S-BS125 F3S-BS155 20 20 20 21 22 24 26 28 30 32 20 20 21 22 24 26 28 30 32 34 20 21 22 24 26 28 30 32 34 35 21 22 24 26 28 30 32 34 35 37 F3S-BS047 F3S-BS067 F3S-BS087 F3S-BS107 20 20 20 20 20 20 20 21 23 24 20 20 20 20 20 20 21 23 24 25 20 20 20 20 20 21 23 24 25 26 20 20 20 20 21 23 24 25 26 27 15 F3S-B WIRING and MOUNTING 2-1 Installation Conditions WARNING Section 2 Do not use the F3S-B on machines that can not be stopped by electrical control in case of an emergency. Do not use the F3S-B in flammable or explosive environments. 2-1-1 Detection Zone and Intrusion Path WARNING Install protective structures around a machine so that you must pass through the detection zone to reach a hazardous part of the machine. Install the F3S-B so that some part of the operator's body remains in the detection zone at all times when the operator works in a hazardous area. Failure to do so may result in serious injury. Correct installation A hazardous part of a machine can be reached only by passing through the sensor detection zone. Some part of the operator's body remains in the detection zone while they are working. Incorrect installation A hazardous part of a machine can be reached without passing through the sensor detection zone. A worker is between the sensor detection zone and a hazardous part of a machine. ! 2-1-2 Safety Distance WARNING ! Always maintain the safety distance between the F3S-B and a hazardous part of a machine. Serious injury may result if the machine does not stop before someone reaches the hazardous part. The "Safety distance" is the minimum distance that must be maintained between the F3S-B and a hazardous part of a machine in order to stop the machine before someone or something reaches it. The calculation of safety distance varies according to with national standards and individual machine standards. It also depends on the direction of intrusion to the detection zone of the light curtain, perpendicular, parallel, or angled approach, and depends on the application, e. g. non-industrial applications where children are present. See related standards for more details. 16 F3S-B # Using EN 999 Formula (See Note 1) Safety distance is calculated based on the following equation. [. . . ] Each failure indication sequence, other than continuous flashing, will repeat after a two-second interval. This repetition will continue until a remedy is effected. Indication Cause Remedy - Check connection of the relay monitoring input. - Check the voltage of the relay monitoring input. [. . . ]