User manual OMRON NE1A-HDY01

[. . . ] Z921-E1-01 DeviceNet Safety NE1A-HDY01 Mobile Console OPERATION MANUAL DeviceNet Safety NE1A-HDY01 Mobile Console Operation Manual Produced April 2009 iv Notice: OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. Always heed the information provided with them. Failure to heed precautions can result in injury to people or damage to property. !WARNING Indicates a potentially hazardous situation which, if not avoided, will result in minor or moderate injury, or may result in serious injury or death. [. . . ] Do not use the Charger for charging any Battery Pack other than the one specified by OMRON. 18 Using the Memory Card Section 1-8 1-8 Using the Memory Card The following data is saved in the Memory Card. · Data to be downloaded to or uploaded from connected devices. · Images of the screen captured by the print screen function of the Mobile Console. Note Use the following OMRON Memory Cards. · HMC-EF183 128 MB · HMC-EF283 256 MB · HMC-EF583 512 MB 1-8-1 Inserting the Memory Card 1, 2, 3. . . Pull out the slot cover for the Memory Card on the Mobile Console. 2. Insert the Memory Card into the slot. Memory Card 3. Return the slot cover to its original position. 19 Using the Memory Card Section 1-8 1-8-2 Removing the Memory Card 1, 2, 3. . . Pull out the slot cover on the Mobile Console for the Memory Card. 2. The eject lever will be extended if it is pressed in. Press it again to eject the Memory Card. Push Push 3. Pull out the Memory Card by grabbing it with your fingers. Memory Card Pull 4. Close the slot cover. 20 Replacing the Clock Battery Section 1-9 1-9 1-9-1 Replacing the Clock Battery Replacing the Clock Battery The Mobile Console uses a battery for the clock to keep the date and time settings when the battery pack is being replaced. If the clock settings are lost, replace the clock battery with the following procedure. Undo the two screws on the back of the Mobile Console using a Phillips screwdriver. Place your finger where the stylus is inserted and pull off the clock battery cover. 4. Press the clock battery in the holder as if to insert it and then remove it. 2. Press in 21 Replacing the Clock Battery 5. Place a new battery in the holder. Section 1-9 6. Replace the clock battery cover and secure it with the screws. Clock Battery Model Use a BR2032 Coin Lithium Battery as the clock battery. Product specifications BR2032 Coin Type Lithium Battery Voltage: 3 V Dimensions: 20. 0 (diameter) × 3. 2 mm (thickness) Panasonic Corporation model Recommended battery IMPORTANT When disposing of the battery, insulate the plus (+) and minus (-) terminals of the battery with tape. Follow all local government regulations as applicable when disposing of the battery. 22 Attaching the Hand Strap Section 1-10 1-10 Attaching the Hand Strap A strap can be attached to the Mobile Console for holding the Console. Attach the strap to the strap hooks for either a left-hand or right-hand grip. 1-10-1 Strap Position Strap hooks Strap hooks Strap Holding in the Right Hand Holding in the Left Hand 1-10-2 Attaching the Strap 1, 2, 3. . . [. . . ] General Specifications of the RB-B2001A Battery Pack . General Specifications of the RB-C2001 Charger . 64 64 64 65 65 66 66 67 67 68 68 Battery Pack Ratings and Specifications. . 63 Mobile Console Ratings and Specifications Section 4-1 4-1 4-1-1 Mobile Console Ratings and Specifications General Specifications Specifications RB-B2001A Battery Pack 0 to 45°C -10 to 60°C 20% to 90% (with no condensation) 3. 5 mm at 5 to 8. 4 Hz, 9. 8 m/s2 at 8. 4 to 150 Hz 196 m/s2 for 11 ms 0. 36 kg max. [. . . ]