User manual OMRON NSH5-SQR10B-V2 10-2010

[. . . ] V090-E1-08 NSH5 Series NSH5-SQR10B-V2 NSH5-SQG10B-V2 Hand-held Programmable Terminal OPERATION MANUAL NSH5 Series NSH5-SQR10B-V2 NSH5-SQG10B-V2 Hand-held Programmable Terminal Operation Manual Revised October 2010 iv Notice: OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. Always heed the information provided with them. Failure to heed precautions can result in injury to people or damage to property. !DANGER !WARNING Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. [. . . ] The following data can be transferred using a Memory Card. · System programs (programs required for operating the PT, such as for communications and fonts) 40 Memory Cards Section 3-5 · Screen data (data used in the PT display) The transfer method is manual transfer (i. e. , the data to be transferred and the transfer direction are selected manually), and operations are specified from the System Menu. Note There are four recommended Memory Card models, each of which, has a different capacity. Model HMC-EF183 HMC-EF283 HMC-EF583 Capacity 128 MB 256 MB 512 MB Memory type Flash memory Flash memory Flash memory A Memory Card can be overwritten approximately 100, 000 times. When using a PC card socket in devices such as notebook computers, use an HMCAP001 Memory Card Adapter. Note Use the Memory Cards recommended by OMRON. Operation may not be correct if other memory cards are used. 3-5-2 Mounting and Removing Memory Cards 1, 2, 3. . . As shown below, to mount the Memory Card to the Memory Card interface first loosen the two screws securing the cover on the top of the PT. Mounting a Memory Card 41 Memory Cards Section 3-5 2. After the screws have been removed, open the cover by pulling it up and forward with a finger. 3. (As this is done, the eject button will pop out. ) Note Removing a Memory Card Tighten the cover to a force of 0. 9 N. Press the eject button to remove the Memory Card. To prevent the Memory Card from popping out and falling, hold the Memory Card with your index finger while pushing the eject button with your middle finger. 3-5-3 Replacing the System Program The system program in the PT can be replaced or upgraded to a higher version. There are two methods that can be used to replace the system program. · Using a recovery/upgrade program · Transferring system program data Note (1) The system program must be version 8. 0 or higher to be installed. (2) Consult your OMRON representative if a system program of a version lower than 8. 0 is to be installed. (3) Use the recovery/update program to install the system program. Using a Recovery/ Upgrade Program Replace the system program if the system program becomes corrupted and the NSH5 will not start or to upgrade the system program in the NSH5. For details on the replacing the system program by using the recovery/update program, select Start - Program - OMRON - CX-One - CX-Designer - How to recover the system program. 42 Memory Cards Section 3-5 Refer to information on the procedure for recovery and update and to the Setup Manual for troubleshooting information if an error is displayed when you use the recovery/update program. Transferring System Program Data The System Program is stored under the CX-Designer's install folder (default location is C:\Program Files\Omron\CX-One\CX-Designer) in folders that are created for each type and version, as follows: \SystemBackup\NSH5\V@_@\bank1: NSH5 system program ("@_@" will be replaced by numbers indicating the system program version. For example "V7_0" is the file for version 7. 0. ) To replace a system program, use Windows Explorer or another method to copy each of the folders for the required system program under \bank1 to the route directory of the Memory Card. For details on methods for transferring data from the Memory Card to the PT, refer to 3-5-4 Transferring Data with Memory Cards. The system backup folder can be created only if CX-Designer is installed from the stand-alone CD-ROM. If the CX-Designer is installed from CX-One, reinstall the system program by following the procedure for using a recovery/ update program described above. 3-5-4 Transferring Data with Memory Cards Using a Memory Card with the PT allows system programs (programs required for operating the PT, such as programs for communications and fonts) and screen data to be transferred to and from the PT. There are several types of data transfers, including manual transfers (in which the data to be transferred and the direction of transfer are selected manually), downloads (in which data is transferred automatically from the Memory Card to the PT), uploads (in which data is transferred automatically from the PT to the Memory Card), and bank specifications (four banks max. ). The transfer method is specified using the System Menu. [. . . ] October 2007 Overall: Changed "NSH Series" to NSH5 Series. " Pages xix, 3 to 6, 8, 9, 23, and 71: Corrected "emergency stop switch". Page xxi: Removed next to last paragraph before section 5. Page 11: Modified the paragraph and figures. Pages 11 to 13, 17, 20: Changed "gasket" to "packing" and "skintop" to "housing. " Pages 28 to 35: Modified sections 2-3 to 2-5. [. . . ]