User manual OMRON SLICE I-O UNITS 11-2007

[. . . ] W455-E1-06 SmartSlice GRT1 Series Slice I/O Units OPERATION MANUAL SmartSlice GRT1 Series Slice I/O Units Operation Manual Revised November 2007 iv Notice: OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. Always heed the information provided with them. Failure to heed precautions can result in injury to people or damage to property. !DANGER !WARNING Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. [. . . ] Use the Setting Tool to make the setting if an input type other than those listed above will be used (GRT-TS2T only). Always set Pin 4 to ON if the DIP switch is to be used to set the input type. If this pin is OFF, the DIP switch settings will not be enabled. The DIP switch settings are read when the power is turned ON. If pin 4 is set to ON, you will not be able to set any functions, including the input type, from the Setting Tool. Always set pin 4 to OFF when using the Setting Tool. Setting Procedure (Example: DeviceNet Configurator) 1, 2, 3. . . In the Network Configuration Window for the Slice I/O Terminal, double-click the icon of the Slice I/O Terminal that is to be set. Alternatively, right-click the icon and select Parameters - Edit. The Edit Device Parameters Window will be displayed. Select the Temperature Input Unit to be edited from the I/O Module Tab Page. Click the Edit Button on the I/O Module Tab Page. The Edit Unit Parameters Window will be displayed. Select the tab page for the input where the input type is to be changed. 173 Temperature Input Units Section 6-4 5. Double-click the Value Setting for the Input Type on the Range/Data Allocation Tab Page and select the desired input type from the pull-down menu. 6. Return to the General Tab Page, click the Download Button, and then click the Reset Button to reset the Unit. Note The Input Type cannot be changed from the Setting Tool if the mode for setting the Input Type with the DIP switch has been specified. The input type range can be set with the DIP switch or the Setting Tool. Range in °C Range in °F Input Type Range GRT1-TS2P Input type PT100 (-200 to 850°C) -200. 0 to 850. 0 PT100 (-200 to 200°C) -200. 0 to 200. 0 -300 to 1, 500 -300 to 380. 0 Range in °F GRT1-TS2PK Input type PT1000 (-200 to 850°C) PT1000 (-200 to 200°C) Range in °C -200. 0 to 850. 0 -200. 0 to 200. 0 -300 to 1, 500 -300 to 380. 0 Note GRT1-TS2T The ranges in the above table are the ranges for which the specified accuracy applies. Range in °C 0 to 1, 700 0 to 1, 700 Range in °F 0 to 3, 000 0 to 3, 000 Input type R S K (-200 to 1300°C) K (0. 0 to 500. 0°C) J (-100 to 850°C) J (0. 0 to 400. 0°C) T E -200 to 1, 300 0. 0 to 500. 0 -300 to 2, 300 0. 0 to 900. 0 -100 to 850 0. 0 to 400. 0 -100 to 1, 500 0. 0 to 750. 0 -200. 0 to 400. 0 0 to 600 -300. 0 to 700. 0 0 to 1, 100 174 Temperature Input Units Input type L (-100 to 850°C) L (0. 0 to 400. 0°C) U N W B PL2 Range in °C Section 6-4 Range in °F -100 to 850 0. 0 to 400. 0 -100 to 1, 500 0. 0 to 750. 0 -200. 0 to 400. 0 -200. 0 to 1, 300 0 to 2, 300 100 to 1, 800 0 to 1, 300 -300. 0 to 700. 0 -300 to 2, 300 0 to 4, 100 300 to 3, 200 0 to 2, 300 Convertible Temperature Ranges GRT1-TS2P The convertible data range depends on the selected input type, as shown in the following tables. Normal Display Mode Type °C PT100 -220. 0 to 870. 0 (-200 to 850°C) PT100 -200. 0 to 220. 0 (-200 to 200°C) Display °F Display F768 to 21FC -320. 0 to 1520. 0 F380 to 3B60 F768 to 0898 -320. 0 to 400. 0 F380 to 0FA0 1/100 Display Mode Type °C Display FFFFAA10 to 153D8 FFFFAA10 to 55F0 °F Display FFFF8300 to 251C0 FFFF8300 to 9C40 PT100 -220. 00 to (-200 to 850°C) 870. 00 PT100 -220. 00 to (-200 to 200°C) 220. 00 -320. 00 to 1520. 00 -320. 00 to 400. 00 Note (1) The display data will be clamped at the minimum or maximum value of the display range between the time when the display range is exceeded, and an off-wire condition is detected. (2) When an off-wire condition is detected, the display data will be 7FFF in normal mode and 7FFF FFFF in 1/100 display mode. (3) If the Unit is subjected to sudden temperature changes, moisture may condense in the Unit and cause incorrect indications. If there is condensation, remove the Unit from service and keep it at a steady temperature for about 1 hour before using it again. (4) If the input temperature exceeds the convertible range, an input error will occur and the ERR indicator for that input will turn ON. If the input temperature is higher than the maximum value, an over range error will occur and the temperature data will be clamped at the maximum value. [. . . ] --1 byte Range of values: 00 to FF hex (0 to 255 decimal) 1 byte --Range of values: 00 to FF hex (0 to 255 decimal) 2 × 4 bytes --Range of values: 8000 0000 to 7FFF FFFF hex (-2, 147, 483, 648 to 2, 147, 483, 647 decimal)*4 1 byte Value: 00 hex --- Write 10 hex 8E hex 01 to 40 hex*1 94 hex Range 0 Write Writes the upper 33 hex and lower limits of range 0. *3 8E hex 01 to 40 hex*1 95 hex Save Write Ranges and Preset Values Writes the range settings and preset value to nonvolatile memory. 10 hex 8E hex 01 to 40 hex*1 97 hex 326 Explicit Messages Explicit message Action on Bus Idle Read/ write Write Function Service code Writes the action performed when the bus enters idle state. 0E hex Command Class Instance Attribute ID ID ID 8E hex 01 to 40 hex*1 98 hex Appendix A Response Data size 1 byte 00 hex: Outputs are cleared on bus idle. 01 hex: Output functionality is maintained on bus idle. ----- Read Reads the action performed when the bus enters idle state. 0E hex 8E hex 01 to 40 hex*1 98 hex 1 byte 00 hex: Outputs are cleared on bus idle. [. . . ]