User manual OMRON V400-H211

[. . . ] Z228-E1-02 V400-H111/211 Handheld 2D Code Reader USER'S MANUAL Introduction Thank you for purchasing the OMRON V400-H111/H211. This manual describes the functions, performance, and application methods of the V400-H111/H211. This manual is intended for personnel with knowledge of electrical systems. Be sure to read and understand this manual thoroughly before using the product, and keep this manual in an easily accessible location for quick reference when required. Introduction Introduction ëÊ 1 èÕ ëÊ 2 èÕ ëÊ 3 èÕ ëÊ 4 èÕ ÇÕǹÇ?Ç Section 1 Section 2 Section 3 Section 4 Section 5 Appendices Introduction Application Considerations (Read and understand this information first. ) Section 1 Product Overview Section 2 Installation and Connections Section 3 Reading 2D Code Section 4 System Settings Section 5 Troubleshooting Appendices Specifications and Dimensions Handheld 2D Code Reader User's Manual V400-H111/211 Introduction READ AND UNDERSTAND THIS DOCUMENT Please read and understand this document before using the products. [. . . ] There are two methods: one is to use the LCD monitor of the Coder Reader, and the other is to use "2DCR Configear" on a personal computer. Overview Making Settings on the Main Body Uploading from the Memory Card Restoring the Factory Setting Data Installing the 2DCR Configear Communicating Using 2DCR Configear Creating Setting Files Using the 2DCR Configear 44 46 53 57 58 60 63 Section 4 System Settings V400-H111/211 User's Manual 43 Section 4 System Settings Overview Measurement conditions and functions can be changed using the LCD monitor of the Coder Reader or using "2DCR Configear" on a personal computer. Using the LCD monitor Creating the Setting Files Set necessary functions in the Setup screen and save them. Communications settings Function settings Section 4 Overview p. 46 Backing Up Data To reflect the data you have set to two or more Code Readers, the data must be backed up to a Memory Card. p. 56 Uploading Data To reflect the data you have set to two or more Code Readers, the data must be uploaded. p. 54 44 V400-H111/211 User's Manual Section 4 System Settings Using "2DCR Configear" on a personal computer Installing the Software Download the application software from home page, and install it. Contact the OMRON representative nearest you regarding the website address. p. 58 Creating Setting Files Create the setting file using the 2DCR Configear. Specify the required settings using the 2DCR Configear, and create as a file. Communications settings Function settings p. 63 Section 4 Overview Uploading Data Upload the created setting data to the Handheld 2D Code Reader. The following two loading methods are available. · Using the 2DCR Configear · Using the Memory Card p. 72 V400-H111/211 User's Manual 45 Section 4 System Settings Making Settings on the Main Body The LCD monitor of the Code Reader can be used to set communication conditions and functions. For this, a Memory Card is required. Basic Operation for Setting Mode In the setting mode, the trigger buttons have different functions. Left: Selection button (to select items, to change settings) Right: Confirmation button (to display the next page, to switch between the item and setting fields) To select [Upload Settings] in the menu screen, carry out the following steps. Confirmation button Section 4 Making Settings on the Main Body Selection button This series of operations whereby pressing the left trigger button to select [Upload Settings] and then pressing the right trigger button to confirm the selection is expressed as "selecting [Upload Settings]". V400-H111/211 User's Manual 46 Section 4 System Settings To set communication conditions or functions, select the desired setting. To change Parity (communication condition), carry out the following steps. Section 4 Making Settings on the Main Body V400-H111/211 User's Manual 47 Section 4 System Settings Starting Setting Mode (Setup Screen) 1. Start setting mode. Setting mode can be started by the following two methods. 1 Turn ON the power to the Code Reader while holding both right and left trigger buttons. When using the AC adapter When using the power supply 2 Insert the Memory Card into the slot while holding both right and left trigger buttons. Section 4 Making Settings on the Main Body The setting mode menu window will be displayed. If the Memory Card does not have a folder called "SETTINGS", "Upload Settings" will not be displayed in the menu window. However, it is still possible to set measurement conditions and functions even if "Upload Settings" is not displayed, but the set data cannot be uploaded. 2. Select [Setup]. The Setup window appears. · Setup window structure 48 V400-H111/211 User's Manual Section 4 System Settings Changing Communication Conditions 1. Select [Communication] in the Setup window. The Setup Communication window appears. 2. Select the item to be changed. The cursor moves to the right of the selected item. Section 4 Making Settings on the Main Body 3. Change the setting. Available settings are shown in the table below. After a new setting is selected, the cursor moves to the item field. Setting item Baud rate (BaudRate) Parity Data length (DataLength) Stop Bit (StopBit) Header (Prefix) Footer (Suffix) FCS * Settings 9, 600 , 19, 200, or 38, 400 None*/Odd/Even 7bits or 8 bits* 1 bit* or 2 bits None*/STX/ESC ETX/LF/CR*/CR+LF ON or OFF* The default settings are indicated with an asterisk. V400-H111/211 User's Manual 49 Section 4 System Settings 4. [. . . ] 340 g V400-H111/211 User's Manual 81 Appendices V400-W22-2M (Unit: mm) Vinyl-insulated Flat cable 2 × 2-dia. , with 2 conductors, length: 0. 2 m 29. 8 2000 200 Connector Connector Bush 30 12. 6 dia. Vinyl-insulated round cable (5-dia. with 4conductors, length: 2 m) Nameplate D-sub, 9-pin Connector V400-W22-5M (Unit: mm) Vinyl-insulated Flat cable 2 × 2-dia. , with 2 conductors, length: 0. 2 m 29. 8 500 (99) 5000 200 Connector Appendices Specifications and Dimensions Bush 30 12. 6 dia. Connector Vinyl-insulated round cable (5-dia. with 4conductors, length: 2 m) Vinyl-insulated round cable (6. 1-dia. with 8 conductors) D-sub, 9-pin Connector Nameplate V400-W22-2M Interface connector Ambient temperature Ambient humidity Ambient environment Materials D-sub, 9-pin, female Operating: 0 to 40°C Storage: -25 to 60°C 35 % to 85 % (with no condensation) No corrosive gases Cable sheath: Heat-resistant vinyl chloride Special connector: PPS, PBT, POM D-sub connector: ABS 30 mm Approx. [. . . ]