User manual OMRON V680

[. . . ] Z262-E1-02A Amplifier and Antennas V680-HA63A V680-HS52 V680-HS63 ID Tags V680-D1KP52MT V680-D1KP66T V680-D1KP66MT V680 Series USER'S MANUAL Introduction Thank you for purchasing a V680-series RFID System. This manual describes the functions, performance, and application methods needed for optimum use of the V680-series RFID System. Please observe the following items when using the RFID System. · Allow the RFID System to be installed and operated only by qualified specialist with a sufficient knowledge of electrical systems. [. . . ] Normal Communications Mode: Lit when an address error occurs. Maintenance Mode: Lit at distance or speed level 4 or higher. Normal Communications Mode: Lit when a Tag memory error occurs. Maintenance Mode: Lit at distance or speed level 3 or higher. Normal Communications Mode: Lit when a no Tag error occurs. Maintenance Mode: Lit at distance or speed level 2 or higher. Normal Communications Mode: Lit when a verification error occurs. Maintenance Mode: Lit at distance or speed level 1 or higher. Normal Communications Mode: Lit when a Tag communications error occurs. The distance level will vary greatly depending on the surrounding environment. The setting position will serve as a guide, but use RUN mode to conduct a sufficient number of tests in the actual operating environment. Values of distance level 4 or above may not be displayed, but this will not affect the RUN mode performance and does not indicate a malfunction. RFID System User's Manual 25 Section 2 Specifications and Performance Cables Specifications Item Model V700-A43/V700-A44 Number of conductors 10 Insulation resistance Dielectric strength 5 M min. (at 500 VDC) between terminals and sheath 500 VAC, 1 min 6 dia. Connector (Controller end)) Connector (Amplifier end) Connection label (Unit: mm) Casing material PVC 26 RFID System User's Manual 15. 5 dia. 15 dia. Section 2 Amplifier Dimensions Item Model V700-A43 Approx. 10m Approx. 20 m Approx. 1, 350 g Length (L1) Weight 51 L1±100 49 Section 2 Specifications and Performance Tags Specifications and Dimensions V680-D1KP52MT · General Specifications Item Memory capacity Memory type Data backup time Memory longevity Ambient operating temperature when communicating Ambient operating temperature when not communicating Ambient storage temperature Ambient operating humidity Degree of protection Vibration resistance Shock resistance Dimensions Materials Weight Metal countermeasures Model 1, 000 bytes (user area) EEPROM 10 years after writing (85°C or less) 100, 000 times per block (25°C) -25 to 85°C (with no icing) V680-D1KP52MT Section 2 Tags -40 to125°C (with no icing) -40 to 125°C (with no icing) 35% to 95% IP68 (IEC 60529) In-house standard for antenna oil resistance (former JEM standard equivalent to IP67g) 10 to 2, 000 Hz, 1. 5-mm double amplitude, acceleration: 150 m/s2, 10 sweeps each in X, Y, and Z directions for 15 minutes each 500 m/s2, 3 times each in X, Y, and Z directions (Total: 18 times) 8 dia. × 5 mm Case: PPS resin, Fill resin: Epoxy resin Approx. 0. 5 g Yes · Dimensions R0. 2 8 -0. 1 dia. 0 5 -0. 1 (Unit : mm) 0 Case material Fill resin PPS resin Epoxy resin When embedding the V680-D1KP52MT into a metal surface, use the V680-HS52 Antenna. Transmission will not be possible if the V680-HS63 Antenna is used. The side with the markings is the communications surface. Mount the Tag with this side facing the Antenna. RFID System User's Manual 27 Section 2 Specifications and Performance V680-D1KP66T/66MT · General Specifications Item Memory capacity Memory type Data backup time Memory longevity Ambient operating temperature when communicating Ambient operating temperature when not communicating Ambient storage temperature Ambient operating humidity Degree of protection Vibration resistance Shock resistance Dimensions Materials Weight Metal countermeasures Model V680-D1KP66T 1, 000 bytes (user area) EEPROM 10 years after writing (85°C or less) 100, 000 times per block (25°C) -25 to 85°C (with no icing) V680-D1KP66MT Section 2 Tags -40 to125°C (with no icing) -40 to 125°C (with no icing) 35% to 95% IP68 (IEC 60529) In-house standard for antenna oil resistance (former JEM standard equivalent to IP67g) 10 to 2, 000 Hz, 1. 5-mm double amplitude, acceleration: 150 m/s2, 10 sweeps each in X, Y, and Z directions for 15 minutes each 500 m/s2, 3 times each in X, Y, and Z directions (Total: 18 times) 34 × 34 × 3. 5 mm Case: PPS resin Approx. 7. 5 g Yes The V680-D1KP66MT is designed to be mounted directly to metal. The V680-D1KP66T and V680D1KP66MT markings are shown in the following diagrams. V680-D1KP66MT V680-D1KP66T V680-D1KP66MT XXXXXX V680-D1KP66T XXXXXX MADE IN JAPAN MADE IN JAPAN The side with the markings is the communications surface. Mount the Tag with this side facing the Antenna. 28 RFID System User's Manual Section 2 Specifications and Performance · Dimensions V680-D1KP66T/66MT Four, R4 25+0. 2 Four, R3 Mounting Hole Dimensions Two, M3 34 32 25+0. 2 Two, 3. 5 dia. Two, 6 dia. 25+0. 2 Section 2 Tags 32 34 3. 5+0. 1 25+0. 2 Case material PPS resin V600-A86 Attachment Four, R5. 5 25+0. 2 Two, 4 dia. Two, M3 37 34 15 25+0. 2 16 25+0. 2 25+0. 2 15 34 37 3. 5 10 4 Case material PPS resin Tag Heat Resistivity · Storing Tags under high temperatures will adversely affect the performance of the internal parts and the service life of the Tags. · An LTPD of 10% was determined during the evaluation for Tags that reached the end of their life after testing under the following test conditions. [. . . ] Check the chemicals carefully in advance. 60 RFID System User's Manual Section 5 Chemical Resistance Chemical Resistance of Tags Applicable Models V680-D1KP66T/66MT Chemical Hydrochloric acid Sulfuric acid 37% 10% 98% 50% 30% 3% At room temperature A A A A A A B A A A A A A A A A A A A A A At 90°C A A B A A A C B A A A B A A A A B B A A A Chemical Sodium hypochlorite Phenol solution Glacial acetic acid Acetic acid Oleic acid Methyl alcohol Ethyl alcohol Ethyl acetate Sebacic acid diethylhexyl Acetone Diethyl ether n-heptane 2-2-4 trimethylpentane Benzene Toluene Aniline Mineral oil Gasoline Insulating oil Dichloroethylene Carbon tetrachloride 95% 95% 5% At room temperature A A A A A A A A A A A A A A A A A A A A A At 90°C A A A A A A A A Nitric acid 60% 40% 10% Section 5 Chemical Resistance of Tags A A A A A A A A A A A A A Hydrogen fluoride solution 40% Chromic acid Hydrogen peroxide solution 40% 28% 3% Sodium hydroxide solution 60% 10% 1% Ammonia solution Sodium chloride Sodium carbonate 28% 10% 10% 20% 2% A: Has no adverse effect, B: May cause discoloration, swelling, etc. , C: Causes deformation, cracks, etc. The above table shows the extent of changes in PPS resin exposed to each chemical at room temperature and at 90°C. If actual chemicals, concentrations, and temperatures are different from those shown in the tables, always conduct tests under the actual conditions in which the Tags are to be used. RFID System User's Manual 61 Section 5 Chemical Resistance Applicable Model V680-D1KP52MT PPS resin is used for case material and epoxy resin for filling material. Refer to the following lists and do not use chemicals that affect PPS and epoxy resin. Tags cannot be used in applications with explosion-proof specifications. Chemicals That Cause Deformations, Cracks, Etc. PPS resin Aqua regia Epoxy resin Aqua regia, chromic acid, sulfuric acid (90% RT), nitric acid (60% RT), ammonia solution, acetone, methylene chloride, phenol Chemicals That May Cause Discoloration, Swelling, Etc. PPS resin Nitric acid (60% RT) Epoxy resin Sulfuric acid (10% RT), nitric acid (10% RT), hydrochloric acid (30% RT), acetic acid (50% RT), oxalic acid, calcium hydroxide, benzine, creosol, alcohol, cyclohexane, toluene, xylene, benzine, grease Section 5 Chemical Resistance of Tags Chemicals that Do Not Affect PPS Resin or Epoxy Resin PPS resin Hydrochloric acid (37%RT), sulfuric acid (98%RT), nitric acid (40%RT), Hydrogen fluoride solution (40%RT), chromic acid (40%RT), hydrogen peroxide (28%RT), sodium hydroxide solution (60%RT), ammonia solution (28%RT), sodium chloride (10%RT), sodium carbonate (20%RT), sodium hypochlorite, phenol solution (5%RT), glacial acetic acid, acetic acid, oleic acid, Methyl alcohol (95%RT), ethyl alcohol (95%RT), Ethyl acetate, sebacic acid, diethylhexyl, acetone, diethyl ether, n-heptane, 2-2-4 trimethylpentane, benzine, toluene, aniline, mineral oil, gasoline, insulating oil, dichloroethylene, carbon tetrachloride Epoxy resin Ammonia, hydrochloric acid (10% RT), potassium hydroxide, petroleum, gasoline, Yushiroken S50, Chemi-Cool Z, Velocity No. [. . . ]