User manual OMRON ZX-E

[. . . ] Z166-E1-02A Smart Sensors: Inductive Displacement Type ZX-E Series OMRON Corporation Industrial Automation Company Sensing Devices Division H. Q. Application Sensors Division Shiokoji Horikawa, Shimogyo-ku, Kyoto, 600-8530 Japan Tel: (81)75-344-7068/Fax: (81)75-344-7107 Regional Headquarters OMRON EUROPE B. V. 4, D-71154 Nufringen, Germany Tel: (49)7032-811-0/Fax: (49)7032-811-199 OMRON ELECTRONICS LLC 1 East Commerce Drive, Schaumburg, IL 60173 U. S. A. Tel: (1)847-843-7900/Fax: (1)847-843-8568 OMRON ASIA PACIFIC PTE. [. . . ] Use the same procedure as for the first point to set the output current value and corresponding measurement result for the second point. 15. Press the ENT Key to confirm the settings. Section 5 Linear Output Confirming Completion of Monitor Focus Settings The display will read OK if monitor focus has been set correctly. The display will be NG if the settings are incorrect. If the settings are incorrect, check the following points and execute the monitor focus again. · Is the measured value set on the sub-display within the measurement distance (with scaling and calculation settings reflected if set)?Are the first and second points separated by at least 1% of the rated measurement distance?Are the current (or voltage) values for the two points the same? · · 106 ZX-E Operation Manual Section 5 DETAILED SETTINGS Correcting Linear Output Values Discrepancies may occur between the linear output current (or voltage) values set on the Amplifier Unit and the actual current (or voltage) values measured due to the conditions for the connected external device or other factors. The linear output correction function can be used to correct this discrepancy. The output values are corrected by entering the correction value for the current or voltage values for any two points. Set the monitor focus function and select either current or voltage output beforehand. p. 103 This section uses a current output as an example. Change the values in this example for voltage output as necessary. 1. Connect the linear output to an external ammeter. Moving to FUN Mode and SPCL Section 5 Linear Output 2. Turn ON the power supply and set the mode switch to FUN. 3. Use the LEFT and RIGHT Keys to display SPCL on the main display. Moving to LEFT-ADJ 4. Press the UP or DOWN Key. The sub-display will flash. 5. Use the UP or DOWN Keys to display SET or ALL. ZX-E Operation Manual 107 Section 5 DETAILED SETTINGS 6. Use the LEFT and RIGHT Keys to display L-ADJ on the main display. The units for the monitor focus settings (mA or V) will be shown on the sub-display. 8. Press the ENT Key. The display will change to the settings for the first point (A). The output current value will be displayed on the main display and the correction will be displayed on the sub-display and the leftmost digit will flash. Set the output current and correction values for the first point. Adjust the correction value on the sub-display so that the ammeter reading and the output current shown on the main display are the same. The larger the correction value, the larger the output current. The correction value can be set within the range -999 to 999. To set a negative value, make the leftmost digit of the sub-display flash and change the value. [. . . ] 107 output settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 P PASS judgement output line . . . . . . . . . . . . . . 38 162 ZX-E Operation Manual Index switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]