User manual ONE FOR ALL URC 4021

[. . . ] CTGAE4P 4021 manual booklet 5/24/04 12:10 PM Page 2 TABLE OF CONTENTS Introduction . 10 Programming The Power Key For The Master Power Macro . 13 Locking Volume Control To One Mode (Global Volume Lock). 13 Unlocking Volume Control For A Single Device (Individual Volume Unlock) . [. . . ] continued on next page. . . 10 CTGAE4P 4021 manual booklet 5/24/04 12:10 PM Page 11 PROGRAMMING A MASTER POWER MACRO (continued) Clearing The Master Power Macro 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Then press POWER once. 3. Press and hold SET until the LED blinks twice, then release SET. The Master Power Macro is now cleared. RE-ASSIGNING DEVICE KEYS The One For All 4 Device Universal Remote Control can be set to control a second PVR, VCR, or DVD player. For example, to control a TV, a cable box, and two DVD players, re-assign the unused VCR/PVR key to operate the second DVD player as follows: 1. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. The VCR/PVR key is now ready to be set up to control your second DVD player. See Programming Device Control on page 8. To re-assign a second VCR or PVR (or DVR) to the unused DVD key, repeat steps 1 through 4. However, in step 3 substitute VCR/PVR for DVD, and in step 4 substitute DVD for VCR/PVR. Now the DVD key will be ready to be set up as your second VCR or PVR (or DVR). See Programming Device Control on page 8. NOTE: Only one device can be assigned to an unused device key at a time. USING CHANNEL SCAN In the CBL/SAT or TV mode, use the FAV key to start a 3-second scan of all channels. Or, if programmed, use the FAV key to scan only your favorite channels to view a desired channel (see Programming Favorite Channel Scan on next page. Press CBL/SAT or TV once. 11 CTGAE4P 4021 manual booklet 5/24/04 12:10 PM Page 12 2. Press FAV once. · If Favorite Channel Scan has been set up, scanning of favorite channels will start with up to 100 channel changes or until stopped by pressing any key. · If Favorite Channel Scan has not been set up, scanning will start with the current channel, and continue up to 100 channel changes or until stopped by pressing any key. 3. To stop scanning channels at any time, press any key once. PROGRAMMING FAVORITE CHANNEL SCAN In the CBL/SAT or TV mode, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when FAV is pressed (see Using Channel Scan on the previous page). NOTE: Favorite channels can only be programmed for one mode. After programming, if FAV is pressed while in another mode, the remote control will start scanning all channels instead (if applicable to the selected device). 1. On the remote control, press CBL/SAT or TV once. 2. 3. Press and hold SET until the LED (red light) blinks twice, then release SET. The LED will blink twice. 4. Use the keypad to enter a favorite channel number (e. g. , 031). Then press SET once. NOTE: If the original remote control required pressing an Enter key to change the channel, also press the ENTER key after the channel number (e. g. , 0 - 3 - 1 - ENTER). On some satellite receivers and cable boxes, you may need to press the SELECT (OK) key instead of ENTER. 5. If desired, repeat step 4 for each channel to be stored, up to a total of 10 channels. NOTE: If you try entering more than 10 channels, the remote control will automatically exit programming. To change your favorite channel list at this point, you will first need to delete the existing list by performing the steps in "Clearing Custom Programming" on page 14. Then, perform the instructions in this section once again. 6. To exit programming with less than 10 favorite channels stored, press and hold SET until the LED blinks twice. Otherwise, the remote control will automatically exit the program after 10 channels have been stored. 12 CTGAE4P 4021 manual booklet 5/24/04 12:10 PM Page 13 CHANGING VOLUME LOCK The One For All 4 Device Universal Remote Control is set at the factory for independent volume control of each selected device. [. . . ] This warranty gives you specific legal rights and you may also have other rights which vary from state to state. To obtain warranty service for a defective product, please return the product, preferably in the original carton, along with your purchase receipt, to the store of original purchase for the first 90 days. A note detailing the complaint would be helpful. The store, at its option, will replace or repair this product if found to be defective. If the unit has been purchased more than 90 days ago, please return it to CT Global Inc. [. . . ]