User manual ONKYO DV-C503

[. . . ] Contents Before Using Your DVD Changer 2 DVD Changer Getting Started 6 DV-C503 Facilities and Connections 10 Instruction Manual Basic Operation 17 Advanced Operation 20 Thank you for purchasing the Onkyo DVD Changer. Please read this manual thoroughly before making connections and turning on the power. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new DVD Changer. Please retain this manual for future reference. Function Setup 30 Others 37 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Setting Digital Audio Out to any other setting could result in digital noise being output that could cause harm your hearing and may also damage your speakers. Notes · Refer to the instructions supplied with the AV component for details on what digital audio formats it is compatible with. · Even if digital audio connections are made, it is also recommended to make analog connections, because some conditions or media may prohibit digital audio output. To digital input (coaxial) Coaxial cable (not supplied) Optical cable (not supplied) An amplifier or receiver with a Dolby Digital or DTS decorder or digital inputs To digital input (optical) VIDEO OUTPUT COMPONENT PR VIDEO AUDIO OUTPUT DIGITAL OUTPUT COAXIAL OPTICAL DVD CHANGER MODEL NO. DV-C503 PB L DO NOT connect the power cord until all connections are complete. Y S VIDEO R To audio input An amplifier or receiver with stereo inputs Making stereo audio connections Using an audio cable (sold separately), make audio connections from the AUDIO OUTPUT L and R jacks to the corresponding jacks on the stereo component. Be sure to set Digital Audio Out setting to "PCM" using the setup menu explained in "Customizing the Settings" starting on page 30. See page 35 for direct information. Notes · Be sure to match the colors of the plugs on the cable with the corresponding jacks on the DVD Changer and the stereo component: red for R (right) audio and white for L (left) audio. · Do not make connections to the PHONO or TUNER jacks on the stereo component. Audio cable (not supplied) Audio (R) Analog signal Audio (L) Digital signal Coaxial plug Digital signal Optical plug Signal flow 16 Turning on Connecting the POWER The DV-C503 is shipped with the main power (POWER) switch in the on position ( ON). When the power cord is plugged in for the first time, the DV-C503 will automatically enter the standby mode and the STANDBY indicator will light (same condition after step 2 below). POWER STANDBY/ON STANDBY indicator Notes · Make sure that all appropriate connections have been completed as described on pages 14 to 16. · Turning on the DVD Changer may cause a momentary power surge, which might interfere with other electrical equipment such as computers. To prevent interference, use a wall outlet on a different circuit. 1 2 Plug the power cord into the power outlet on the wall. Press POWER to switch on the main power. The DVD Changer enters standby mode. The STANDBY indicator lights up. Notes · The buttons on the remote controller do not operate if the POWER switch is set to OFF. · To switch off the main power, press POWER again. STANDBY/ON 3 Press STANDBY/ON on the DVD Changer or remote controller. The DVD Changer turns on and the STANDBY indicator turns off. It takes several seconds to read the disc in the disc tray. Notes · You can turn on the DVD Changer by pressing 0 or £/8. · To put the DVD Changer in the standby mode, press STANDBY/ON on the DVD Changer, or remote controller. Be sure to set the volume to minimum before putting the DVD Changer in the standby mode for the next use to avoid sudden loud sound reproduction. · While the STANDBY indicator lights up, the DVD Changer can receive signals from the remote controller. However, if you press POWER on the DVD Changer to switch off the main power, the remote controller cannot be used to turn on the DVD Changer. · Setting the STANDBY button to standby does not shut off the power completely. 17 DVD VCD CD Basic Playback Before playing · DVD-Video, Video CD, CD can be played with the DVD Changer (see "Playable Discs" on page 6). · When playing DVD-Video or Video CD with video features, turn on the TV and set the TV to the DVD Changer's input. · If an audio system is connected to the DVD Changer, turn on the audio system and set it to the DVD Changer's input. Warning If the DVD Changer is connected to the TV or amplifier through the analog audio jacks, do not play DTS-encoded discs. Excessive noise may be output from the analog stereo jacks, which may damage the connected equipment. [. . . ] No sound or inaccurate sound is reproduced. · The DVD Changer is in repeat playback mode, memory playback mode, or random playback mode, etc. · The TV is not set to receive the output signals from the DVD Changer. · The DVD Changer is not properly connected. · A wrong sound signal conversion method (Digital Audio Out) is selected. [. . . ]