User manual ONKYO DV-CP500

[. . . ] Contents Before Using Your DVD Changer 2 DVD Changer Getting Started 6 DV-CP500 Facilities and Connections 10 Instruction Manual Basic Operation 17 Advanced Operation 20 Thank you for purchasing the Onkyo DVD Changer. Please read this manual thoroughly before making connections and turning on the power. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new DVD Changer. Please retain this manual for future reference. Function Setup 30 Others 37 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] When the power cord is plugged in for the first time, the DV-CP500 will automatically enter the standby mode and the STANDBY indicator will blink for about 10 seconds, then light (same condition after step 2 below). While the STANDBY indicator is blinking, operation buttons will not function. POWER STANDBY/ON STANDBY indicator Notes · Make sure that all appropriate connections have been completed as described on pages 14 to 16. · Turning on the DVD Changer may cause a momentary power surge, which might interfere with other electrical equipment such as computers. To prevent interference, use a wall outlet on a different circuit. 1 2 Plug the power cord into the power outlet on the wall. Press POWER to switch on the main power. The DVD Changer enters standby mode. The STANDBY indicator blinks for about 10 seconds, then lights. While the STANDBY indicator is blinking, operation buttons will not function. Notes · The buttons on the remote controller do not operate if the POWER switch is set to OFF. · To switch off the main power, press POWER again. STANDBY/ON 3 Press STANDBY/ON on the DVD Changer or remote controller. The DVD Changer turns on and the STANDBY indicator turns off. It takes several seconds to read the disc in the disc tray. Notes · You can turn on the DVD Changer by pressing 0 or £/8. · To put the DVD Changer in the standby mode, press STANDBY/ ON on the DVD Changer, or remote controller. Be sure to set the volume to minimum before putting the DVD Changer in the standby mode for the next use to avoid sudden loud sound reproduction. · While the STANDBY indicator lights up, the DVD Changer can receive signals from the remote controller. However, if you press POWER on the DVD Changer to switch off the main power, the remote controller cannot be used to turn on the DVD Changer. · Setting the STANDBY button to standby does not shut off the power completely. 17 DVD VCD CD Basic Playback Before playing · DVD-Video, Video CD, CD can be played with the DVD Changer (see "Playable Discs" on page 6). · When playing DVD-Video or Video CD with video features, turn on the TV and set the TV to the DVD Changer's input. · If an audio system is connected to the DVD Changer, turn on the audio system and set it to the DVD Changer's input. Warning If the DVD Changer is connected to the TV or amplifier through the analog audio jacks, do not play DTS-encoded discs. Excessive noise may be output from the analog stereo jacks, which may damage the connected equipment. To reproduce DTS surround sounds, digital connection to an amplifier with a DTS decoder is needed. About the DVD , VCD and CD marks in the pages related to disc operation DVD means the function or title is related to DVD-Video operation. VCD means the function or title is related to Video CD operation. CD means the function or title is related to audio CD operation. Starting Playback DISC SKIP 4/¢ STOP 7 PLAY/PAUSE £/8 DISC 1-DISC 5 Disc tray 0 OPEN/CLOSE 1 Press 0 OPEN/CLOSE. The disc tray opens. If the DVD Changer is in standby mode when 0 OPEN/CLOSE button is pressed The DVD Changer turns on and the disc tray opens. In this case, it takes several seconds until the disc tray opens. I To stop playback Press STOP 7. When you press PLAY/PAUSE £/8 to restart playback, playback starts from the location where you stopped playback because the location index is stored in memory. Note The location where playback resumes may vary depending on the disc or the scene where you stopped. 2 Resuming playback from the beginning Place a disc on the disc tray. To insert or remove another disc by changing the tray position, press DISC SKIP. Put the disc in the tray with the label side facing up. Place the disc in the correct guide on the disc tray. Press STOP 7 again after stopping playback to clear the location index memory, then press PLAY/PAUSE £/8 to start playback. I To select a disc Press one of DISC 1 to DISC 5 buttons or press DISC SKIP repeatedly. 3 Press PLAY/PAUSE £/8. The disc tray closes and playback starts. [. . . ] No sound or inaccurate sound is reproduced. · The DVD Changer is in repeat playback mode, memory playback mode, or random playback mode, etc. · The TV is not set to receive the output signals from the DVD Changer. · The DVD Changer is not properly connected. · A wrong sound signal conversion method (Digital Audio Out) is selected. [. . . ]