User manual ONKYO HT-R430

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6. 1ch Home Theater System HT-S680 AV Receiver (HT-R430) Front Speakers (SKF-330F L/R) Center Speaker (SKC-330C) Surround Speakers (SKM-330S L/R) Surround Back Speaker (SKB-330) Powered Subwoofer (SKW-420) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Turning On & First Time Setup. . . . . 32 Basic Operation Playing your AV components . . . . . . . [. . . ] · If the test tone is not produced by a speaker, or it's produced by a speaker other than that shown on the display, you may have wired the speakers incorrectly and you should check your connections (see page 18). 32 First Time Setup Assigning Digital Inputs to Input Sources Changing the TAPE/MD/CDR Display If you connect an -compatible Onkyo MiniDisc recorder or CD recorder to the TAPE IN/OUT jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver. TUNING / PRESET 2, 3 TUNING / PRESET MASTER VOLUME STANDBY/ON ENTER STANDBY MASTER VOLUME A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP STANDBY/ON CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD STANDBY ENTER A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD 1 To enjoy Dolby Digital and DTS, you must connect your DVD player to the AV receiver by using a digital audio connection (coaxial or optical). With this function, you can assign digital inputs to input sources. For example, if you connect your DVD player to DIGITAL IN OPTICAL, you'll need to assign that input (OPT) to the DVD input source. You can change the assignments as follows. Note: Make sure you also set your digital sources to send out a digital signals. Please refer to the digital sources' manual. 1, 2 1 TAPE Press the [TAPE] input selector button so that "TAPE" appears on the display. 2 TAPE 1 DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER Press the input selector button for the source that you want to assign. (Digital inputs cannot be assigned to the TUNER input source. ) Press and hold down the [TAPE] input selector button (about 3 seconds) to set the display. Repeat this step to select TAPE, MD, or CDR. CD 2 DIGITAL INPUT Press the [DIGITAL INPUT] button. The current assignment appears. 3 DIGITAL INPUT Press the [DIGITAL INPUT] button repeatedly to select COAX, OPT or "­ ­ ­ ­" (analog). 33 Playing Your AV Components Basic AV Receiver Operation 2 STANDBY/ON DISPLAY TUNING / PRESET 4 1 MASTER VOLUME ENTER ON STANDBY REMOTE MODE RECEIVER TAPE/AMP DVD 1 Subwoofer's rear panel INPUT SELECTOR 1 V1 2 V2 3 V3 CD 4 7 TAPE TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP 5 MULTI CH 6 DVD MD STANDBY 8 TUNER 9 CD CDR A SPEAKERS B +10 --/--CD 0 DIMMER CLR SLEEP CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER DISC CH VOL 4 MIN MAX MULTI CH 1 2 TOP MENU MENU OUTPUT LEVEL SP A / B MUTING ENTER 1 AV receiver DVD VIDEO 1/VCR VIDEO 2 Remote controller Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] button, and then use the INPUT SELECTOR buttons. On the remote controller, the [V1], [V2], and [V3] buttons select the VIDEO 1/VCR, VIDEO 2, and VIDEO 3 input sources respectively. VIDEO 3 TAPE TUNER CD 2 AV receiver A SPEAKERS B Remote controller Use the SPEAKERS [A] and [B] buttons on the AV receiver or the [SP A/B] button on the remote controller to select the speaker set that you want to use. Pressing the remote controller's [SP A/B] button cycles through the following settings: Speaker Set A Speaker Set A&B Speaker Set B Off. The A and B speaker indicators show whether each speaker set is on or off. Indicators Note that when speaker set B is turned on, speaker set A is reduced to 2. 1-channel playback. When you select DVD or another video component, on your TV you'll need to select the video input that's connected to the AV receiver's MONITOR OUT. 3 4 AV receiver MASTER VOLUME Remote controller VOL To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. The volume can be set to MIN, 1 through 79, or MAX. The AV receiver is designed for home theater enjoyment and has a wide volume range for precise adjustment. To set the level of the subwoofer, use the OUTPUT LEVEL control. Because our ears are less sensitive to very low bass sounds, there's a temptation to set the level of the subwoofer too high. As a rule of thumb, set the subwoofer level to what you think is the optimal level, and then back it off slightly. 5 34 Select a suitable listening mode and enjoy!See page 40. Playing Your AV Components--Continued Displaying Source Information ON STANDBY REMOTE MODE RECEIVER TAPE/AMP DVD RECEIVER INPUT SELECTOR You can display various information about the current input source as follows. [. . . ] · To control Onkyo CD player or MD/CD recorder, point the remote controller at that component. Recording Can't record?· On your recorder, make sure the correct input is selected. · To prevent signal loops and damage to the AV receiver, input signals are not fed through to outputs with the same name (e. g. , TAPE IN to TAPE OUT, or VIDEO 1 IN to VIDEO 1 OUT). 53 Troubleshooting--Continued Others The sound changes when I connect my headphones?· When a pair of headphones is connected, the listening mode is set to Stereo, unless it's already set to Stereo, Mono, Direct. [. . . ]