User manual ONKYO HT-R518

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AV Receiver HT-R518 Instruction Manual Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Turning On & First Time Setup. . . . . 33 Basic Operation Playing your AV components . . . . . . . [. . . ] Muting is cancelled when the AV receiver is set to Standby. DIMMER Using the Sleep Timer SLEEP With the sleep timer, you can set the AV receiver so that it turns off automatically after a specified period. Press the [RECEIVER] REMOTE MODE button, and then press the remote controller's [SLEEP] button repeatedly to select the required sleep time. You can set the sleep time from 90 to 10 minutes in 10 minute steps. The SLEEP indicator appears on the display when the sleep timer has been set, as shown. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears. SLEEP indicator DISPLAY MASTER VOLUME ON/STANDBY TUNING PRESET STANDBY ENTER PURE AUDIO PURE AUDIO MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP RETURN AUX INPUT PHONES CINEMA FILTER SETUP MIC VIDEO L AUDIO R LATE NIGHT TONE MOVIE/TV MUSIC GAME DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE CLEAR AV RECEIVER HT-R518 PHONES Setting the Display Brightness You can adjust the brightness of the display. Remote controller Press the [RECEIVER] REMOTE MODE button, and then press the remote controller's [DIMMER] button repeatedly to select: dim, dimmer, or normal brightness. To cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you'll shorten the sleep time by 10 minutes. 40 Common Functions--Continued 7Using Headphones For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver's PHONES jack. Displaying Source Information You can display various information about the current input source as follows. Press the [RECEIVER] REMOTE MODE button, and then press the [DISPLAY] button repeatedly to cycle through the available information. LATE NIGHT ON/STANDBY STANDBY PURE AUDIO PURE AUDIO MULTI CH PHONES CINEMA FILTER Notes: · Always turn down the volume before connecting your headphones. · While the headphones plug is inserted in the PHONES jack, the speakers are turned off. · When you connect a pair of headphones, the listening mode is set to Stereo, unless it was already set to Pure Audio, Mono, Stereo, or Direct, in which case it stays the same. · When the multichannel DVD input is selected, only the front left and front right channels can be heard in the headphones. Note: · This procedure can also be performed on the AV receiver by using its [DISPLAY] button. The following information can typically be displayed: Input source & volume*1 Signal format*2 or sampling frequency Input source & listening mode *1 When AM or FM radio is used, the band, preset number, and frequency are displayed. *2 If the input signal is analog, or AM or FM radio is selected, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about 3 seconds, then the previous display reappears. Interpreting Surround Channel Information A BC A: The number of front channels (front left, front right, and center). B: The number of surround channels (surround left and surround right). C: LFE channel for subwoofer (1 means yes). 41 Common Functions--Continued Specifying the Digital Signal Format The following table shows the display indicator for each digital signal format. Format Dolby Digital DTS PCM PCM Display Normally, the AV receiver detects the format of digital input signals automatically. However, if you experience either of the following issues when playing PCM or DTS sources, you can specify the signal format manually. · If the beginnings of tracks from a PCM source are cut off, try the PCM setting. · If noise is produced when fast forwarding or rewinding a DTS CD, try the DTS setting. MASTER VOLUME ON/STANDBY TUNING PRESET STANDBY ENTER PURE AUDIO PURE AUDIO MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP RETURN AUX INPUT PHONES CINEMA FILTER SETUP MIC VIDEO L AUDIO R LATE NIGHT TONE MOVIE/TV MUSIC GAME DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE CLEAR AV RECEIVER HT-R518 DIGITAL INPUT 1 DIGITAL INPUT Press and hold the AV receiver's [DIGITAL INPUT] button for about 3 seconds. 2 DIGITAL INPUT While "Auto" is displayed (about 3 seconds), press the [DIGITAL INPUT] button repeatedly to select: PCM, DTS, or Auto. [. . . ] · To control an Onkyo component that's not connected via , or another manufacturer's component, point the remote controller at that component. Be sure to enter the appropriate remote control code first (page 64). Others The sound changes when I connect my headphones · When a pair of headphones is connected, the listening mode is set to Stereo, unless it's already set to Stereo, Mono, Direct, or Pure Audio, in which case it stays the same. How do I change the language of a multiplex source · On the "Audio Adjust" menu, change the "Input (Mux)" setting to Main or Sub (page 55). The functions don't work · To use , you must make an connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally (page 32). [. . . ]