User manual ONKYO HT-R580

[. . . ] Contents 7. 1ch Home Theater System Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 HT-S5300 AV Receiver (HT-R580) Speaker Package (HTP-580) Front Speakers (SKF-580 L/R) Center Speaker (SKC-580) Surround Speakers (SKR-580 L/R) Surround Back Speakers (SKB-580 L/R) Subwoofer (SKW-580) Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Turning On & Basic Operations . . . . . . 21 Universal Port Option Dock for iPod® (UP-A1) Advanced Operations . . . . . . . . . . . . . . . . . 33 Instruction Manual Controlling iPod & Other Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Others. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Thank you for purchasing an Onkyo 7. 1ch Home Theater System. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new 7. 1ch Home Theater System. Please retain this manual for future reference. En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Mono This setting specifies the channel to be used for playing any 2-channel digital source such as Dolby Digital, or 2channel analog/PCM source in the Mono listening mode. Input Ch(Mono) L+R: Both the left and right channels are output. Right: Only the right channel is output. · These settings are disabled when: · a pair of headphones is connected, or · the "Audio TV OUT" setting is set to "On" ( 40) and an input selector other than HDMI is selected. · Speakers that you set to "No" or "None" in the "Sp Config (Speaker Configuration)" ( 35) cannot be selected. · The Center, Right, Subwoofer and Front High distances can be set up to 5 ft. (1. 5 m) more or less than the "Left" distance. For example, if the "Left" distance is set to 20 ft. (6 m), the Center, Right, Subwoofer, Front High Left and Front High Right distances can be set between 15 and 25 ft. · The Surround and Surround Back distances can be set up to 5 ft. (4. 5 m) less than the "Left" distance. For example, if the "Left" distance is set to 20 ft. (6 m), the Surr Right, Surr Left, Surr Back R and Surr Back L distances can be set between 5 and 25 ft. (1. 5 and 7. 5 m). Level Cal (Level Calibration) Menu Level Cal Dolby Settings PLIIx Music (2ch Input) These settings apply to only 2-channel stereo sources. If you're not using any surround back speakers, these settings apply to Dolby Pro Logic II, not Dolby Pro Logic IIx. With this setting, you can broaden the width of the front stereo image when using the Dolby Pro Logic IIx Music listening mode. Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. Left, FrontHigh Left, Center*1, FrontHigh Right, Right, Surround Right, SurrBack Right, SurrBack Left, Surround Left ­12 dB to 0 dB to +12 dB in 1 dB step. Subwoofer*1 ­15 dB to 0 dB to +12 dB in 1 dB step. Note · Speakers that you set to "No" or "None" in the "Sp Config (Speaker Configuration)" ( 35) cannot be selected. · The speakers cannot be calibrated while a pair of headphones is connected or the AV receiver is muted or "Audio TV OUT" setting is set to "On" ( 40). *1 For the center speaker and subwoofer, the level settings made by using AUDIO are saved. En 36 Dimension ­3 to 0 to +3 With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music listening mode. Higher settings move the sound field backward. If the stereo image feels too wide, or there's too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it's in mono, or there's not enough surround sound, move it backward. [. . . ] Start playback of the DVD player/recorder, and confirm the following. · The power of the AV receiver is turned on automatically, and input with the DVD player/recorder connected is selected. · The power of the TV is turned on automatically, and input with the AV receiver connected is selected. Following the operating instructions of the TV, select "Use the TV speakers" from the menu screen of the TV, and confirm that the audio is output from the speakers of the TV, and not from the speakers connected to the AV receiver. [. . . ]