User manual ONKYO HT-S590

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5. 1ch Home Theater System HT-S590 AV Receiver (HT-R340) Front Speakers (SKF-340F L/R) Center Speaker (SKC-340C) Surround Speakers (SKM-340S L/R) Subwoofer (SKW-340) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Turning On & First Time Setup. . . . . 34 Instruction Manual Basic Operation Playing your AV components . . . . . . . [. . . ] For the TAPE input selector, the setting changes in this order: TAPE MD CDR HDD 35 Playing Your AV Components Basic AV Receiver Operation 2 STANDBY/ON DISPLAY TUNING / PRESET 4 MASTER VOLUME ON/STANDBY REMOTE MODE RECEIVER TAPE DVD 1 INPUT SELECTOR 1 1 V1 2 V2 3 V3 CD 4 ENTER STANDBY 5 MULTI CH 6 DVD MD 7 A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP 8 TUNER 9 CD CDR TAPE CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD +10 --/--- 0 DIMMER CLR SLEEP HDD DISC ALBUM CH VOL 4 MULTI CH 1 TOP MENU MENU 2 SP A / B MUTING ENTER PLAYLIST PLAYLIST 1 AV receiver DVD VIDEO 1/VCR VIDEO 2 Remote controller RECEIVER Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] button, and then use the INPUT SELECTOR buttons. On the remote controller, the [V1], [V2], and [V3] buttons select the VIDEO 1/VCR, VIDEO 2, and VIDEO 3 input sources respectively. VIDEO 3 TAPE TUNER V1 CD V2 V3 DVD TAPE TUNER CD 2 AV receiver A SPEAKERS B Remote controller SP A / B Use the SPEAKERS [A] and [B] buttons on the AV receiver or the [SP A/B] button on the remote controller to select the speaker set that you want to use. Pressing the remote controller's [SP A/B] button cycles through the following settings: Speaker Set A Speaker Set A&B Speaker Set B Off. The A and B speaker indicators show Indicators whether each speaker set is on or off. Note that when speaker set B is turned on, speaker set A is reduced to 2. 1-channel playback. 3 4 AV receiver MASTER VOLUME Start playback on the source component. When you select DVD or another video component, on your TV you'll need to select the video input that's connected to the AV receiver's MONITOR OUT. Remote controller VOL To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. The AV receiver is designed for home theater enjoyment and has a wide volume range for precise adjustment. Note: The maximum master volume level is affected by the subwoofer volume level. 5 36 Select a suitable listening mode and enjoy!See "Using the Listening Modes" on page 46. Playing Your AV Components--Continued Using the Multichannel Input You can display various information about the current input source as follows. RECEIVER ON/STANDBY REMOTE MODE RECEIVER 1 V1 RECEIVER TAPE DVD INPUT SELECTOR 2 V2 3 V3 CD DISPLAY MD Press the [RECEIVER] button, and then press the [DISPLAY] button repeatedly to cycle through the available information. MULTI CH 4 7 TAPE 5 MULTI CH 6 DVD 8 TUNER 9 CD CDR +10 --/--- 0 DIMMER CLR SLEEP HDD The following information can typically be displayed for input sources. Input source & volume*1 Signal format*2 or sampling frequency Input source & listening mode DISC ALBUM CH VOL The multichannel input is for connecting a component with individual 5. 1-channel analog audio output jacks, such as a DVD player or MPEG decoder. See page 27 for hookup information. RECEIVER Press the [RECEIVER] button followed by the [MULTI CH] button so that MULTI CH indicator appears on the display. Audio from the multichannel input will now be used for the DVD input source. MULTI CH indicator MULTI CH Note: · While the multichannel input is selected, the Speaker Configuration settings on page 52 are ignored, and signals from the multichannel input are fed to the front left, front right, center, surround left, and surround right speakers and subwoofer regardless of those settings. *1 When AM or FM radio is used, the band, preset number, and frequency are displayed. *2 If the input signal is analog, or AM or FM radio is selected, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about 3 seconds, then the previous display reappears. Interpreting Surround Channel Information A BC Displaying Source Information ON/STANDBY REMOTE MODE A: The number of front channels (front left, front right, and center). B: The number of surround channels (surround left and surround right). If there's surround back channel information, this number will be 3. C: LFE channel for subwoofer (1 means yes). RECEIVER 1 V1 RECEIVER TAPE DVD INPUT SELECTOR 2 V2 3 V3 CD 5 AUDIO SUBTITLE TEST TONE CH SEL PLAY MODE 6 LEVEL- MD LEVEL+ DISPLAY DISPLAY OR-EQ L NIGHT CINE FLTR RC-646S 37 Using the Tuner Listening to the Radio TUNING MODE TUNING TUNING / PRESET Tuning into Radio Stations Auto Tuning Mode 1 TUNING MODE MASTER VOLUME STANDBY/ON ENTER Press the [TUNING MODE] button so that the AUTO indicator appears on the display. STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD 2 TUNING / PRESET TUNER SETUP ENTER Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found. With the built-in tuner, you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. 1 TUNER Use the [TUNER] input selector button to select either AM or FM. [. . . ] · Make sure you've selected the correct remote controller mode (page 12). · If you've connected an -capable Onkyo MD recorder, CD recorder, or next generation HDD-compatible component to the TAPE IN/OUT jacks, or a DS-A1 Remote Interactive Dock to the VIDEO 3 IN jacks, for the remote controller to work properly, you must set the Input Display to MD, CDR, or HDD (see page 35). · To control an Onkyo component that's connected via , point the remote controller at the AV receiver. 56 Troubleshooting--Continued Recording Can't record?· On your recorder, make sure the correct input is selected. [. . . ]