User manual ONKYO HT-SP908

[. . . ] Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AV Receiver TX-SR605 AV Amplifier Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 First Time Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 TX-SA605 TX-SA8560 Instruction Manual Basic Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Advanced Operations. . . . . . . . . . . . . . . . . . . . 69 Advanced Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Zone 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Thank you for purchasing an Onkyo AV Receiver/ AV Amplifier. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver/ AV Amplifier. Please retain this manual for future reference. Controlling Other Components . . . . 90 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] The main menu appears onscreen. 2 Use the Up and Down [ ]/[ ] buttons to select "2. Speaker Setup, " and then press [ENTER]. Speaker Settings Speaker Config Speaker Distance Level Calibration Equalizer Settings 2 Press and hold down the [TAPE] or [GAME/TV] input selector button (about 3 seconds) to change the setting. Repeat this step to select MD, CDR, or DOCK. For the TAPE input selector, the setting changes in this order: MD CDR DOCK TAPE For the GAME/TV input selector, the setting changes in this order: DOCK GAME/TV 3 Use the Up and Down [ ]/[ ] buttons to select "1. Speaker Settings, " and then press [ENTER]. The Speaker Settings menu appears. 2­1. Speaker Settings Speakers Impedance Speakers Type 6 ohms Normal Note: DOCK can be selected for the TAPE input selector or GAME/TV input selector, but not both at the same time. 51 First Time Setup--Continued 4 Use the Up and Down [ ]/[ ] buttons to select "Speaker Impedance, " and then use the Left and Right [ ]/[ ] buttons to select: 4 ohms: Select if the impedance of any speaker is 4 ohms or more but less than 6. 6 ohms: Select if the impedances of all speakers are between 6 and 16 ohms. Use the Up and Down [ ]/[ ] buttons to select "Speakers Type, " and then use the Left and Right [ ]/[ ] buttons to select: Normal: Select this if you've connected your front speakers normally. Bi-Amp:Select this if you've connected your front speakers for bi-amped operation. The Setup menu closes. 2 Use the Up and Down [ ]/[ ] buttons to select "6. Miscellaneous, " and then press [ENTER]. OSD Setup 5 3 Use the Up and Down [ ]/[ ] buttons to select "2. OSD Setup, " and then press [ENTER]. OSD Setup Immediate Display Monitor Type Display Position TV Format On 4:3 Bottom Auto 6 4 Note: This procedure can also be performed on the AV receiver/AV amplifier by using its [SETUP] button, arrow buttons, and [ENTER] button. TV Format Setup (not North American models) You must specify the TV system used in your area. 1 Press the [RECEIVER] button followed by the [SETUP] button. The main menu appears onscreen. Use the Up and Down [ ]/[ ] buttons to select "TV Format, " and then use the Left and Right [ ]/[ ] buttons to select: Auto: Select this to automatically detect the TV system from the video input signals. NTSC: Select if the TV system in your area is NTSC. PAL: Select if the TV system in your area is PAL. When you've finished, press the [SETUP] button. The setup menu closes. 5 Note: This procedure can also be performed on the AV receiver/AV amplifier by using its [SETUP] button, arrow buttons, and [ENTER] button. 52 First Time Setup--Continued AM Frequency Step Setup (on some models) You must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted. 1 Press the [RECEIVER] button, followed by the [SETUP] button. [. . . ] Select another listening mode. The following settings can be made for the component video, S-Video, and composite video inputs You must use the buttons on the unit to make these settings. While holding down the input selector button for the input source that you want to set, press the [SETUP] button. Use the Left and Right [ ]/[ ] buttons to change the setting. Press the [SETUP] button when you've finished. [. . . ]