User manual ONKYO HTP-2

[. . . ] SPEAKER SYSTEM HTP-2 Instruction Manual HTP-2 SPEAKER SYSTEM English SL-105 POWERED SUBWOOFER D-L5 × 5 SATELLITE SPEAKERS Thank you for your purchase of the Onkyo speaker system. Please read this manual thoroughly before using it. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new speaker system. Please retain this manual for future reference. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] The HTP-2 features the SL-105 subwoofer with L/R mixing circuits and a builtin cut-off filter as the subwoofer and the D-L5 speakers with an aluminum cabinet and OMF-cone as the five satellite speakers. Simply connect the speakers to your AV amplifier or receiver for superb surround audio playback. Control positions and names I Subwoofer SL-105 Front panel 2 POWERED SUBWOOFER FREQUENCY OUTPUT LEVEL 3 Rear panel SL-105 SL-105 INPUT FROM AMP/RECEIVER C SPEAKER LEVEL + R _ _ L + LINE INPUT AUTO STANDBY L (MONO) OFF ON OUTPUT TO SPEAKERS R + R _ _ L + 50Hz 200Hz MIN MAX D AB POWER 1 To AC outlet A Low-level input jacks (LINE INPUT) Connect these jacks to the LINE OUT jacks of the amplifier etc. B Auto standby switch (AUTO STANDBY) This switch is used to turn on and off the auto standby function. ON: This activates the auto standby function. If a constant level signal is not received from the amplifier (or receiver) over a period of a few minutes, the SL-105 automatically enters the standby state. If a constant level signal is later received from the amplifier (or receiver), the power is automatically turned back on. OFF: Deactivates the auto standby function. Notes: · The auto standby function operates on the existence or absence of a constant level input signal. If the auto standby function does not operate properly, try slightly increasing (or decreasing) the output level of the amplifier or receiver. (Note that output levels of some amplifiers and receivers cannot be adjusted. For more details regarding your components, refer to the instruction manual supplied with them. ) · If noise from peripheral components causes the incorrect operation of the auto standby function, or if outputting low volumes (i. e. , during the nighttime) causes the auto standby function to activate, turn off the auto standby function. · The auto standby function only operates while the power switch for the SL-105 is turned on. C Speaker-level input terminals (INPUT FROM AMP/RECEIVER) Connect these input terminals to the speaker output terminals of your amplifier or receiver. D Speaker-level output terminals (OUTPUT TO SPEAKERS) The speaker-level signal to the front speakers is output from these terminals. 1 2 3 Power switch (POWER) and indicator Pressing this button turns the power on (the indicator lights). Pressing the button again turns the power off (the indicator goes out). Red: Unit is in standby mode Green: Unit is in operation Frequency adjusting knob (FREQUENCY) Use this knob to select the high-frequency range at which you wish to cut off the signal to the subwoofer. The screws should stick out from the wall at a length between 9 and 17 mm. (Requesting such a screw from a manufacturer is recommended. ) 7. 5 mm or less 3. 5 mm or less 9 to 17 mm Installation using commercially-available stands and fixtures The speaker bottoms are equipped with screw holes so that you can attach commercially-available stands or mounting fixtures for a variety of mounting options. (M5 x 2 screw holes; 60-mm pitch) Note: When attaching an accessory item to a speaker, be careful of the length of the screws used. Use only screws that provide the required strength with a screw length between 7 and 10 mm. TV or Screen nt Fro t lef r ake spe SubCenter woofer speaker (SL-105) Fro n righ t spe t ake r I Using spacers Attaching the supplied spacers is recommended for obtaining the best sound quality. Also, by attaching the provided spacers, the speakers will not slide easily for a more stable installation. Surround left speaker Listener Surround right speaker 5 Connecting the speakers For safety reasons, do not turn on any devices or components until you have completed all wiring procedures. I Connecting the satellite speakers Note: The nominal impedance of this speaker system is 6 . Use only amplifiers capable of handling this impedance. · Connect the input terminals on the rear of the satellite speakers to the speaker output terminals on the AV amplifier or receiver using the supplied speaker cables as shown in the diagram to the left. [. . . ] · Pin-connector cable(s) are disconnected at the LINE INPUT jacks. · Speaker cables are not properly connected to the INPUT FROM AMP/ RECEIVER terminals. · The speaker setting at the receiver is set to "Subwoofer No. " · The input signal is so small that the unit entered the standby state. Small sound output · Speaker cables are connected to the INPUT FROM AMP/RECEIVER terminals with reversed phase. [. . . ]