User manual ONKYO RC-632M REMOTE CONTROL CODES

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] No: Select if no subwoofer is connected. Menu selection Setting target Setting options (default setting underlined) If you connect a video component to a component video input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to COMPONENT VIDEO IN 2, you must assign "IN2" to the "BD/DVD" input selector. Here are the default assignments. Input selector BD/DVD VCR/DVR CBL/SAT GAME AUX TV/CD Default assignment IN1 ----IN2 ----------------- HDMI Input Menu HDMI Input PORT If you connect a video component to an HDMI input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to HDMI IN 2, you must assign "HDMI2" to the "BD/DVD" input selector. Here are the default assignments. Input selector BD/DVD VCR/DVR CBL/SAT GAME AUX TV/CD PORT Default assignment HDMI1 ----HDMI2 HDMI3 ------------- BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, TV/ CD, PORT IN1, IN2: Select a corresponding component video input that the video component has been connected. - - - - -: Select if you're not using the COMPONENT VIDEO OUT. Note · If you connect a component (such as UP-A1 Dock that seated iPod) to the UNIVERSAL PORT jack, you cannot assign any input to PORT selector. Digital Audio (Digital Audio Input) Menu Digital Audio BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, TV/ CD, PORT HDMI1, HDMI2, HDMI3: Select a corresponding HDMI input that the video component has been connected. - - - - -: Select if you're not using the HDMI OUT. Each HDMI input cannot be assigned to two input selectors or more. When HDMI1 - HDMI3 have already been assigned, you must set first any unused input selectors to "- - - - -", or you will be unable to assign HDMI1 - HDMI3 to input selector. Note · When an HDMI IN is assigned to an input selector as explained here, the digital audio input for that input selector is automatically set to the same HDMI IN ( 28, Digital Audio (Digital Audio Input)). · If you connect a component (such as UP-A1 Dock that seated iPod) to UNIVERSAL PORT jack, you cannot assign any input to PORT selector. · Do not assign the component connected with the HDMI input to TV/CD selector when you set "TV Control" setting to "On" ( 32). · Speakers that you set to "No" or "None" in the "Sp Config (Speaker Configuration)" ( 29) cannot be selected. · The Center, Right, and Subwoofer distances can be set up to 5 ft. (1. 5 m) more or less than the Left distance. For example, if the Left distance is set to 20 ft. (6 m), the Center, Right, and Subwoofer distances can be set between 15 and 25 ft. · The Surround distances can be set up to 5 ft. For example, if the Left distance is set to 20 ft. (6 m), the SurrRight and SurrLeft distances can be set between 5 and 25 ft. (1. 5 and 7. 5 m). Input Ch(Mux) Main: The main channel is output. M/S: Both the main and sub channels are output. Mono This setting specifies the channel to be used for playing any 2-channel digital source such as Dolby Digital, or 2channel analog/PCM source in the Mono listening mode. [. . . ] Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable. Note · When the audio return channel (ARC) function is used with TV for HDMI 1. 4, it should not be this connection ( 32). Confirm the settings. Turn on the power for all connected components. Turn off the power of the TV, and confirm that the power of the connected components is turned off automatically with the link operation. Turn on the power of the Blu-ray Disc/DVD player/recorder. [. . . ]