User manual ONKYO RDV-1.1 SETTING MEMO

[. . . ] Super Audio CD & DVD Audio/Video Player RDV-1. 1 Instruction Manual WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Install in accordance with the manufacturer's instructions. [. . . ] · Do not use a power cord other than the one supplied with the RDV-1. 1, which is designed exclusively for use with the RDV-1. 1 and should not be used with any other component. · Never disconnect the power cord from the RDV-1. 1 while the other end is still plugged into a wall outlet. Always disconnect the power cord from the wall outlet first. · The RDV-1. 1 is shipped with the Power switch in the On position ( ). When the power cord is connected for the very first time, the RDV-1. 1 will go on Standby and the Standby indicator will light up. · To completely shutdown the RDV-1. 1, set the Power switch to the Off position ( ). DVD CHANGER MODEL NO. DPC-7. 4 AC INLET 1 2 Plug the supplied power cord into the RDV-1. 1's AC INLET. Plug the other end of the power cord into a suitable AC wall outlet. The Standby indicator comes on only if the Power switch is in the On position ( ). 42 Connecting--Continued Turning On the RDV-1. 1 Standby/On Power 1 Set the Power switch to the On position ( ). The Standby indicator lights up. 2 Press the [Standby/On] button. The display light ups, the On indictor lights up, and the Standby indicator goes off. The very first time you turn on the RDV-1. 1, the Initial Setup menu appears onscreen (see page 44). Press the [Standby/On] button again to enter Standby. Turning On the RDV-1. 1 with the Remote Controller On Standby I On 1 4 7 +10 Search S TV Input 2 5 8 0 Memory M 3 6 9 + T V CH - T V VOL Clear Dimmer D Amp Input Input Amp Input DVD V1 V2 V3 Mode DVD Audio Sel DVD Amp VCR TV Zoom On Top Picture Control Menu Menu + CH Zoom L Mode Enter VOL Ret urn p Setu Display Muting The RDV-1. 1 must be in Standby mode for this procedure to work. 1 Mode DVD Press the [DVD] Mode button to select DVD mode. This is the mode for controlling the RDV-1. 1. 2 On Press the [On] button. To set the RDV-1. 1 to Standby, press the [Standby] button. 43 Initial Setup This chapter explains the settings you need to make the very first time the RDV-1. 1 is turned on. The On-Screen Language menu appears next. On Standby I TV Input 1 4 7 +10 Search S 2 5 8 0 Memory M 3 6 9 + T V CH - T V VOL Clear Dimmer D Amp Input Input Amp Input DVD V1 V2 V3 Mode DVD Amp VCR TV Zoom On Picture Control Top Enter Audio Sel Menu Menu 2 + CH Zoom L Mode Enter VOL Ret urn p Setu Display Muting Last Memory Rec LM Audio Step/Slow Random RD Subtitle Angle Resolution Use the Up and Down [ ]/[ ] buttons to select a language, and then press [Enter]. See page 82 for more information on the language options. The i. LINK Output Setting menu appears next. First Time Setup The very first time you turn on the RDV-1. 1, the Initial Setup menu appears onscreen. 3 Use the Up and Down [ ]/[ ] buttons to select Off or On for the i. LINK Output Setting (i. LINK), and then press [Enter]. See page 77 for more information on the i. LINK Output Setting. If the i. LINK Output Setting is set to Off, the Analog Audio Out menu appears next. Here you need to make a few settings to get the RDV-1. 1 up and running. You can change these settings later (see page 69). 1 Remote controller Enter Use the Up and Down [ ]/[ ] buttons to select a TV shape, and then press [Enter]. If it's set to On, the Initial Setup menu closes. 4 Enter Select 4:3 Letter box or 4:3 Normal if you have a 4:3 TV. Select 16:9 Widescreen if you have a widescreen TV. See page 73 for more information. On the Analog Audio Out menu, use the Up and Down [ ]/[ ] buttons to select 2 Channel or Multi Channel (default), and then press [Enter]. [. . . ] You're too far away from the RDV-1. 1. Remedy Set the i. LINK Output Setting to Off (page 77). Set the i. LINK Output Setting to Off (page 77). Use only ISO 9660 Level 2 format discs (page 11). Use the correct filename extension (page 11). Only files in the first session of a multisession disc can be played (page 11). [. . . ]