User manual ONKYO SKF-501F

[. . . ] Contents 2. 1ch Speaker Package Getting Started Important Safety Instructions . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting to know Your Speaker Package . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Make sure that the plug is readily operable (easily accessible) at all times. Package Contents Make sure your box contains all of the items below. If anything is missing, contact the nearest Onkyo dealer. · 2 front speakers (SKF-501F) with removable stands and cables (3 m) · Subwoofer (SKW-501) · RCA cable for connecting the subwoofer (3 m) · 4 floor pads for the subwoofer Declaration of Conformity We, ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3. MIYAGI · 8 rubber spacers for the front speakers ONKYO EUROPE ELECTRONICS GmbH The alphabet displayed at the end of the product name found in catalogs and on package represents the color of the system. Though the color varies, the specifications and operations are the same. En-3 Getting to know Your Speaker Package Front speakers (SKF-501F) Rear Speaker Explanation with the Stand Removed 4 1 2 D Keyhole slots 3 A Stand fixing screw B Stand C Speaker cable Removing the Speaker Stands You can remove the stands from the speakers and place the speakers on the floor or in a cabinet if you like. The stands must be removed when the speakers are to be mounted on a wall by using the keyhole slots or commercially available speaker brackets. (A) (B) (C) 5 6 These keyhole slots can be used to wall-mount the speaker. E Speaker mount/bracket inserts These threaded inserts can be used to attach the speaker either horizontally or vertically to a speaker mount or bracket. Note: Use commercially available M5 (5 mm) screws to attach the speaker to a speaker mount or bracket. F Speaker terminals These push terminals are for connecting the speaker to your DVD/AV receiver with the speaker cables. The speaker cables are color-coded for easy identification. Simply connect each cable to the same-colored positive speaker terminal. Using the Rubber Spacers with the Speaker Stands Removed If you want to use the speakers without the stands, we recommend using the supplied rubber spacers to achieve the best possible sound. The rubber spacers prevent the speakers from moving around, providing a more stable setup. Rubber spacers 1. Remove screw (A), and then slide off the stand as shown. Disconnect the wires from the speaker terminals. Detach the speaker cables from the stand. Remove screws (B) and (C), remove the stand, and then detach the speaker cables. To replace the stand: Perform the above procedure in reverse order. First, connect the speaker cables, and then replace the screws in the following order: (C), (B), (A). Bottom of the speaker En-4 Getting to know Your Speaker Package--Continued Wall Mounting The speakers can easily be wall mounted by using the keyhole slots. To prevent the speaker from vibrating against the wall, attach four of the supplied spacers to the keyhole fins on the rear of each speaker. Mounting vertically To mount the front speakers vertically, use the keyhole slot shown to hang each speaker on a screw that's securely screwed into the wall. Rubber spacers Subwoofer (SKW-501) Front 1 Rear Keyhole slot for vertical wall mounting 2 To AC outlet 3 Caution: A mounting screw's ability to support a speaker depends on how well it's anchored to the wall. If you have hollow walls, screw each mounting screw into a stud. If there are no studs, or the walls are solid, use suitable wall anchors. [. . . ] Then, dry immediately with a clean cloth. Do not use rough material, thinners, alcohol or other chemical solvents or cloths since these could damage the finish, remove the panel lettering, or cause discoloration. If you are using a chemical cloth, always follow the instructions that come with the cloth. For dust accumulated on grilles, use a vacuum cleaner or brush it off. Specifications Powered Subwoofer (SKW-501) Type: Input sensitivity/impedance: Maximum output power: Frequency response: Cabinet capacity: Dimensions (W × H × D): Bass-reflex 140 mV / 20 k 150 W (Dynamic Power) 27 Hz­150 Hz 24. 5 L 230 × 425 × 412 mm Weight: Drivers unit: Power supply: Power consumption: Other: 9. 1 kg 20 cm Cone Woofer × 1 AC 220-240 V, 50/60 Hz 105 W Auto Standby function En-7 Front Speaker (SKF-501F) Type: Impedance: Maximum input power: Output sound pressure level: Frequency response: Crossover frequency: Cabinet capacity: Dimensions (W × H × D): w/stand Weight: w/stand 2 Way Closed Type 6 120 W 78 dB/W/m 60 Hz­50 kHz 3 kHz 2L 140 × 355 × 93 mm 178 × 404 × 145 mm 1. 8 kg 2. 6 kg Drivers unit: Terminal: Keyhole slots: Grille: Other: 8 cm Cone Woofer × 2 2. 5 cm Balanced Dome Tweeter × 1 Spring Type Color Coded (red/black) 2 Fixed Magnetic shielding Specifications and appearance are subject to change without prior notice. Troubleshooting Symptom Possible cause The speaker cables are not connected properly. [. . . ]