User manual ONKYO TX-DS484

[. . . ] Contents Before using AV Receiver TX-DS484 Instruction Manual Important Safeguards. . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Supplied accessories. . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the PARAMETER SELECTOR® button to display the LFE LEVEL parameter, and press the PARAMETER CONTROLLER /® buttons to set the value. You can set the LFE LEVEL parameter for the Dolby digital or DTS playback. In general, leave this parameter to 0dB. Pressing the PARAMETER CONTROLLER /® buttons repeatedly toggles the values. With the Dolby digital sound, the parameter value changes as shown on the left. With the DTS sound, the parameter value changes in the following order: +10dB, 0dB, ­dB. Also, refer to "LFE level attenuation" on page 22. Press the PARAMETER SELECTOR ® button. POWER ON VOLUME ON/OFF parameter appears. Press the PARAMETER CONTROLLER /® buttons to toggle between ON and OFF. ON: Power On Volume function is enabled. OFF: Power On Volume function is disabled. Display the desired setting and press the PARAMETER SELECTOR ® button. Refer to page 18 for more information on the Power On Volume function. Note: Even if the parameter has already been set to ON, turn it OFF, then turn it ON again to enable the Power On Volume function. 1, 3 TEST TONE Test Tone (Remote controller only) Use the remote controller and produce the test tone to adjust the level of the connected speakers. Each speaker produces the test tone (pink noise) in the following order: 2 CH SEL TEST TONE LEFT (Front L ch) SUBWOOFER (Subwoofer) CENTER (Center ch) L-SURROUND (L-Surround) RIGHT (Front R ch) R-SURROUND (R-Surround) LEVEL 2. To adjust the level of each speaker, press the CH SEL button to select a speaker and press the LEVEL/ buttons to raise or lower the level. The test tone should sound at the same level when you hear it in your listening position. You can adjust the level in the range between ­12dB and +12dB. Press the TEST TONE button to complete adjustment. Parameter selector This chart shows how the display changes when the PARAMETER SELECTOR buttons are pressed. Selecting a parameter and pressing the PARAMETER CONTROLLER button will change the value or setting for the selected parameter. START Subwoofer YES / NO PARAMETER SELECTOR PARAMETER SELECTOR FRONT Speaker Distance 0. 3 ~ 9m, 1 ~ 30ft FRONT Speaker LARGE / SMALL Center Speaker Distance 0. 3 ~ 9m, 1 ~ 30ft Center Speaker LARGE / SMALL / NONE Surround Speaker Distance 0. 3 ~ 9m, 1 ~ 30ft LFE Level Attenuator Dolby Digital: 0dB / ­10dB / ­dB DTS: +10dB / 0dB / ­dB POWER ON VOLUME ON / OFF QUIT Surround Speaker LARGE / SMALL / NONE 16 Selecting a sound source Follow the steps below to select a device to play the sound source. 2. Make sure that the SPEAKERS A indicator is lit on the display. [. . . ] The sound of the playback source is not heard. 5 5 17 Also refer to the respective instruction manuals of the video disc player, video cassette recorder, TV monitor, etc. , that compose your entertainment system. 27 Specifications AMPLIFIER SECTION 55 watts per channel min. RMS at 8 ohms, 2 channels driven from 20 Hz to 20 kHz with no more than 0. 08% total harmonic distortion. RMS at 6 ohms, 2 channels driven from 1 kHz with no more than 0. 1% total harmonic distortion. Continuous Power output (DIN) 75 watts × 5 at 6 ohms Maximum Power output (EIAJ) 100 watts × 5 at 6 ohms Total Harmonic Distortion: 0. 08% at rated power (Front) IM Distortion: 0. 08% at rated power (Front) Damping Factor: 60 at 8 ohms (Front) Input Sensitivity and Impedance PHONO: 2. 5 mV, 50 kohms LINE (CD, TAPE, DVD, VIDEO 1, 2): 200 mV, 50 kohms MULTICHANNEL INPUT (FRONT L/R, SURROUND L/R, CENTER): 200 mV, 50 kohms (SUBWOOFER): 36 mV, 50 kohms DIGITAL 2 (COAXIAL): 0. 5 Vp-p, 75 ohms VIDEO IN (DVD, VIDEO 1, 2): 1 Vp-p, 75 ohms Output Level and Impedance Rec out (TAPE, VIDEO 2): 200 mV, 2. 2 kohms Pre out (SUBWOOFER): 1 V, 2. 2 kohms VIDEO OUT (VIDEO 2, MONITOR): 1 Vp-p, 75 ohms Phono Overload: 110 mV RMS at 1 kHz, 0. 5% T. H. D. [. . . ]