User manual ONKYO TX-SV444

[. . . ] Please retain this manual for future reference. Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Turning On & First Time Setup. . . . . 32 Basic Operation Playing your AV components . . . . . . . 36 Using the Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] None: Select if no center speaker is connected. Note: · If the Front setting in step 4 is set to Small, the Large option cannot be selected. Testing the speakers To test that all of the speakers are working properly, press the remote controller's [TEST TONE] button. LISTENING MODE STEREO SURROUND AUDIO SUBTITLE RANDOM REPEAT TEST TONE TEST TONE CH SEL PLAY MODE LEVEL- LEVEL+ DISPLAY L NIGHT CINE FLTR RC-645S 6 Use the Down [ ] button to select "Surround, " and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Small: Select if the surround speakers are small. Large: Select if the surround speakers are large. None: Select if no surround speakers are connected. Note: · If the Front setting in step 4 is set to Small, the Large option cannot be selected. The test tone will be output by each speaker in turn and the name of each speaker will appear on the display. To turn off the test tone, press the [TEST TONE] button again. · If the test tone is not produced by a speaker, or it's produced by a speaker other than that shown on the display, you may have wired the speakers incorrectly and you should check your connections (see pages 18, 19). · If the test tone is not produced by a speaker and its name does not appear on the display, you may have set the speaker settings incorrectly (see page 34). 7 SETUP Press the [SETUP] button. When you want to go back up one menu level to "SP Config, " press the [RETURN] button. 35 Playing Your AV Components Basic AV Receiver Operation 2 STANDBY/ON DISPLAY TUNING / PRESET 4 MASTER VOLUME ON/STANDBY REMOTE MODE RECEIVER TAPE DVD 1 INPUT SELECTOR 1 1 V1 2 V2 3 V3 CD 4 ENTER STANDBY 5 MULTI CH 6 DVD MD 7 A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP 8 TUNER 9 CD CDR TAPE CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD +10 --/--- 0 DIMMER CLR SLEEP HDD DISC ALBUM CH VOL 4 MULTI CH 1 GUIDE TOP MENU PREVIOUS MENU 2 SP A / B MUTING ENTER PLAYLIST PLAYLIST 1 AV receiver DVD VIDEO 1/VCR VIDEO 2 Remote controller RECEIVER Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] button, and then use the INPUT SELECTOR buttons. When this setting is changed, all radio presets are deleted. Press and hold the TUNING Up or Down [ ]/[ ] button. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. 1 2 Press the [SETUP] button to display "0. Hardware Setup, " and then press [ENTER]. Use the Up and Down [ ]/[ ] buttons to select "AM Freq, " and then use the Left and Right [ ]/[ ] buttons to select: 10 kHz: Select if 10 kHz steps are used in your area. 9 kHz: Select if 9 kHz steps are used in your area. Setup closes. The American model changes FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. For other models it's 0. 05 MHz steps for FM and 9 kHz or 10 kHz steps for AM. When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator appears on the display, as shown. TUNED AUTO FM STEREO 3 Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. [. . . ] · Passing cars and airplanes can cause interference. · Concrete walls weaken radio signals. · If nothing improves the reception, install an outdoor antenna (page 21). Remote Controller The remote controller doesn't work?· Make sure that the batteries are installed with the correct polarity (page 9). [. . . ]