User manual OPTICON C 37

[. . . ] CCD Barcode Scanner C37 The C37 is a handheld linear image scanner. Specifications Manual Opticon C37 Specifications Manual All information subject to change without notice. Document History Model Number: Edition: Date: C37 1 2009-10-05 Specification Number: Original Spec Number: SS09046 SS09045 Copyright 2009 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. Serial Number A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. [. . . ] Storage Temperature and Humidity Temperature: -20° to +60° C Humidity: 5 to 95% RH 4. 3. Ambient Light Immunity Decoding performance is guaranteed when the range of illumination on a barcode surface is between zero and the following values: Incandescent light Fluorescent light 10, 000 lx 10, 000 lx Figure 1: Ambient light immunity 8 Opticon C37 Specifications Manual Conditions Barcode Sample: OPTOELECTRONICS Test Sample PCS: Resolution: Symbology: Quiet Zone: N/W Ratio: Distance: Angle: Curvature: Power Supply Voltage: 0. 9 0. 25 mm 9-digit Code 39 10 mm 1:2. 5 70 mm = 0° = 15° = 0° = 5. 0 V Direct light or specular reflection light from a source should be prevented from entering the acceptance area. Note: , and respectively represent pitch, skew and tilt. Please see section 7 for how these values are defined. 5. Framework and Structure This product consists of an optical section, a decode and a communication section. The optical section includes a CCD for decoding and an illumination LED. The decode section decodes scanned data and carry out signal processing. The communication interface section converts 3. 3V power supply and outputs decoded data and signals to the buzzer, LEDs and trigger key The C37 with RS-232C interface requires the supplied AC adaptor. The C37 with Wedge or USB interface uses bus power. It does not require an AC adaptor. OPTICAL SECTION ILLUMI NATIO N LED DECODE& COMMUNICATION CONTROL SECTION TRIGGER KEY BUZZER LED POWER SUPPLY 3. 3V +4. 56. 6V +6. 0V +5. 0V AC ADAPTER HOST CCD ASIC + ROM / RAM INTERFACE (RS-232C / USB / WEDGE) HOST Figure 2: Framework and structure diagram 9 Opticon C37 Specifications Manual 5. 2. RS232 Parameter Operating voltage Operating current 1: LED: ON, Buzzer: OFF Operating current 2: LED: ON, Buzzer/LED: OFF Rush current peak Stand-by current 1: Auto-trigger OFF Stand-by current 2: Auto-trigger ON Symbol VOP IOP IOP IPEAK IPRE IPRE Min 4. 5 -- -- -- -- -- Typ 6. 0 95 150 350 35 60 Max 6. 6 110 180 400 40 70 Unit V mA mA mA mA mA 5. 2. 2. USB / Wedge Parameter Operating voltage Operating current 1: LED: ON, Buzzer: OFF Operating current 2: LED: ON, Buzzer/LED: OFF Rush current peak Stand-by current 1: Auto-trigger OFF Stand-by current 2: Auto-trigger ON Symbol VOP IOP IOP IPEAK IPRE IPRE Min 4. 5 -- Typ 5. 0 95 150 Max 5. 5 110 180 300 40 70 Unit V mA mA mA mA mA -- -- -- 250 35 60 5. 3. Input Specifications Parameter Power supply voltage Power supply frequency Maximum supply current Inrush current AC 90 V to 265 V 47 Hz to 63 Hz 0. 5 A 50 A/AC 240 V Value 10 Opticon C37 Specifications Manual 5. 3. 2. Output Specifications Parameter Output voltage Power ripple Maximum current Short-circuit protection 6. 0 V ±5% 120 m Vp-p max. (rated load) 2A Available Value Conditions · · · Connect 1 resistance to a power supply line in series and measure the current by the voltage between both ends of resistance. Power supply voltage is measured at a connector terminal area. The current value depends on the interface type and host computer to which the device is connected. 6. CCD Specifications Parameter Light-emitting element Emission wavelength Scanning method Scanning speed Number of pixels Specification Red LED 630 ±10 (25° C) CCD Linear Image Sensor 200 ±20 2500 Unit -- nm -- scans/s -- Notes: Refer to chapter 15, "Trigger and Read Options, " to read about the scan modes. Refer to chapter 7, "Technical Specifications, " to read about scanning performance. 11 Opticon C37 Specifications Manual 7. Technical Specifications The conditions for technical specifications are as follows, unless otherwise specified in each section. Conditions Ambient temperature and humidity: Ambient light: Background: Room temperature (5 to 35º C) Room humidity (45% to 85% RH) 500 to 1000 lx Barcode = black Space = white Margin = white Background of label = black 6. 0 V (RS-232C) / 5. 0 V (USB, Wedge) Approve the performance when decoding is successful in all ten tests. (Decoding is deemed successful when completed in 0. 5 seconds or less. ) Power supply voltage: Decoding test: 7. 1. [. . . ] Please install and use the equipment according to the instruction manual. FCC Part 15 Subpart B Class B: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 17. 3. RoHS RoHS: The restriction of the use of certain hazardous substances in electrical and electronic equipment, 2002/95 EC. 34 Opticon C37 Specifications Manual 18. [. . . ]