User manual OPTICON MSL 2000

[. . . ] Undecoded Laser Scan Engine MSL 2000 The MSL 2000 is an undecoded compact laser bar code scan engine that can be installed in various handheld products. Specifications Manual Opticon MSL 2000 Specifications Manual All information subject to change without notice. Document History Model Number: Edition: Date: MSL 2000 1 2006-08-01 Specification Number: Original Spec Number: SS06026 SS05045 Copyright 2008 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. Serial Number A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. [. . . ] 24 Figure 13: Mechanical drawing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 4 Opticon MSL 2000 Specifications Manual 1. Abstract This document provides specifications of the MSL 2000 laser scan engine. 2. Overview The MSL 2000 (hereafter called "the scan engine") is an undecoded compact laser barcode scan engine that can be installed in various handheld products such as portable terminals. When scanning a target at the minimum decode distance, this scan engine can scan up to 44 mm wide at an angle of 44°. The use of a short-wavelength red laser beam enhances the visibility of the laser beam when scanning barcodes. This scan engine scans barcodes using laser light and outputs those barcode images as a logic level signal (hereinafter called the "signal"). This scan engine also outputs timing waveforms (signals) synchronized with scanning. Such timing waveforms (signals) are hereinafter referred to as "TIMING". This scan engine can be turned on and off via an external input signal, "POWER EN". The laser light emission of this scan engine can be controlled via an external input signal, "LASER EN". This scan engine is compliant with RoHS. 3. Dimensions W 20. 4 x D 14. 0 x H 11. 0 mm 3. 2. Weight 3. 9 g (max. ) 5 Opticon MSL 2000 Specifications Manual 4. Operating Temperature and Humidity Temperature: -20 to 65° C Humidity: 5 to 90% RH 4. 2. Storage Temperature and Humidity Temperature: -30 to 70° C Humidity: 5 to 90% RH 4. 3. Tilt of Laser Scan Line (The maximum tilt in between both ends of the scan line. ) · Less than 1. 2 degrees upward tilt from the scan origin (MM mirror). · Maximum of 3. 1 millimeters when measured at the point 150 millimeters away from the scan origin. (The measurement is taken at the center of the scan line. ) 6. 1. 2. Curvature of Scanning (The maximum gap between the straight line connecting both ends of the laser scan line and the actual laser scan line. ) · Less than 1. 27 degrees curvature from the scan origin. · Maximum of 3. 3 millimeters when measured at the point 150 millimeters away from the scan origin. (The measurement is taken at the center of the scan line. ) Curvatu re Tilt H o riz o n ta l L in e Figure 2: Curvature 9 Opticon MSL 2000 Specifications Manual 7. Technical Specifications The conditions for technical specifications are as follows, unless otherwise specified in each section. Conditions Ambient temperature and humidity: Ambient light: Background: Room temperature (5 to 35º C) Room humidity (45% to 85% RH) 500 to 900 lx Barcode = black Space = white Margin = white Background of label = black 3. 3 V Over 95% decode Power supply voltage: Decoding test: 7. 1. [. . . ] Drop Test: Fixed an MSL 2000 inside a dummy case and dropped it on its top, bottom, front, back, left, right, top-left, top-right, bottom-left and bottom-right sides from 1. 8 meters above the concrete floor. Repeated this routine 10 times. 11. 3. Vibration Strength No malfunction occurred after the following vibration test. Vibration test: Increase the frequency of the vibration from 12 Hz to 200 Hz with accelerated velocity 3. 3 G for over 10 minutes. [. . . ]