User manual OREGON SCIENTIFIC BAR112HGLA

[. . . ] DIGITAL WEATHER FORECASTER WITH REMOTE THERMO-HYGRO SENSOR AND RADIO CONTROLLED CLOCK MODEL NO. : BAR112HGA USER'S MANUAL INTRODUCTION Congratulations on your purchase of the Weather forecaster with cable free sensor and radio-controlled calendar clock BAR112HGA. This unit has a large four-line liquid crystal display (LCD) for displaying weather forecast information, in/outdoor temperatures and relative humidity, radio frequency (RF) controlled calendar clock and daily alarm. Also, the main unit can support up to three remote sensors. Other features include day of week display in three abbreviated languages, crescendo alarm, and interchangeable clock display modes. MAIN FEATURES: MAIN UNIT A A1 B C D E K L M N MA X T EMP RH MA X J I H G F 1 1 MODE/ SE MODE /SETT ME M ME M CHANN EL CH AN NE L 433 MHZ CABLE FREE MO DEL N O. [. . . ] No signal received in search mode. COMFORT LEVEL INDICATORS The comfort level indicators COM, WET or DRY will tell you if the curent environment is comfortable, too wet or too dry. The comfort indicator will appear on the display when the following conditions are satisfied: Indicator displays on the unit Temperature Range Humidity Range Shows that the Current Environment Ideal range for both relative humidity and temperature Contains excess moisture. Contains inadequate moisture 20°C to 25°C 40%RH(68°F to 77°F) 70%RH COM -5°C -+ 50°C OVER(23°F - 122°F) 70%RH -5°C -+ 50°C Below (23°F - 122°F) 70%RH Less than 20°C( 68°F) or More than 25°C (77°F) 40%RH to 70%RH REMOTE SENSOR SCANNING The unit can be set to automatically scan and display readings from the remote sensors and indoor readings. When the remote-sensor scanning mode is active, the display will show the readings from one channel for about 4-second and then proceed to the next channel display. To activate the remote-sensor scanning mode: · Press and hold [CHANNEL] for 2 seconds. To deactivate the remote-sensor scanning mode: · Press either [CHANNEL], [MEM], [HI/LO], [ s ], [ON/OFF] (TEMP % RH AL) 7 WET DRY No Indicator No comment GB GB TEMPERATURE, HUMIDITY & PRESSURE TREND INDICATORS The temperature-trend, humidity-trend and pressure-trend indicators show the trends of collected readings. Arrows indicate a rising, steady or falling trend. MAXIMUM AND MINIMUM TEMPERATURE AND HUMIDITY The maximum and minimum recorded temperature and humidity readings will automatically be stored in the memory. To display the maximum and minimum display memory: 1. Press [MEM] once to display the maximum temperature and humidity and press [MEM] again to display minimum temperature and humidity. The respective indicators, MAX or MIN will be displayed. To clear the memory: · Press and hold [MEM] for 2 seconds. Arrow indicator Temperature Trend Rising Steady Falling Arrow indicator Humidity Trend Rising Steady Falling If you press [MEM] now, the maximum and minimum recordings will have the same values as the current ones until different readings are recorded. Arrow indicator HOW TO USE CHANNEL-1 TEMPERATURE/ HUMIDITY ALARM Rising Steady Falling Pressure Trend Upper and lower temperature and humidity limits for Channel-1 can be set so that an alarm activates when the limits are exceeded. The high and low temperature and humidity displays are selected by sequentially pressing [ HI/LO ]. Note: If the reading goes above or below the measuring range of the main unit or the remote unit ( stated in specification), the display will show "HHH" or "LLL". 8 The high-low displays are as follows: Sequence Pressing HI/LO once Pressing HI/LO twice Pressing HI/LO third time Pressing HI/LO fourth time Respective Display Enters HI temperature display Enters HI humidity display Enters LO temperature display Enters LO humidity display display. The respective HI, LO or both indicators will be displayed to signify the status of the alarm. If a channel other than channel-1 is selected, the display will switch to channel-1 and flash when the alarm activates. If left untouched, the alarm will activate for 1 minute. Press either [CHANNEL], [MEM], [HI/LO], [ s ], [ON/OFF] (TEMP % RH AL) to momentarily stop the alarm. The alarm will activate again if the limit continues to exceed the set limit. Note: If a second limit is passed while an alarm is active, the first alarm will complete its 1-minute cycle and the alarm will continue to activate for a second minute to indicate that a second limit has been surpassed. Enter the setting mode by pressing [HI/LO]. Display will show "---" to indicate such deactivation and will not sound at the previously set limit. To disable a sounding alarm: · Press either [CHANNEL], [MEM], [HI/LO], [ s ], [ON/OFF] (TEMP % RH AL) To set a high or low temperature or humidity alarm: 1. The strength of the reception will remain until the next scanning cycle takes place. [. . . ] Here are a few product care instructions: 1. If the unit comes in contact with water, dry it immediately with a soft lint-free cloth. Do not clean the unit with abrasive or corrosive materials. Abrasive cleaning agents may scratch the plastic parts and corrode the electronic circuit. [. . . ]