User manual OUTLAW 990

[. . . ] Model 990 7. 1 Channel Preamp/Processor Owner's Manual Version 1. 0 Owner's Manual Warnings Please Read First Outdoor Antenna Grounding­If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Lightning­For added protection for the unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power-line surges. [. . . ] Please note that proper configuration and placement of your speakers is critical for achieving the best possible surround-sound reproduction. Here are some basic recommendations you should consider when positioning your speakers: Automatic Setup Using the included setup microphone, the Model 990 can automatically determine your speaker configuration, set the proper amount of delay so that sound coming from the different speakers arrives at your ears at the same time, and balance the levels of the different channels so they are all equal. You will still need to configure inputs and a few other features manually, but the auto setup procedure does most of the job for you. Before you begin automatic setup, make sure all of the connections have been made between the Model 990 to your source components, amplifier(s), and speakers, and that the Model 990 and your video display are turned on. To perform automatic setup: 1. Press the MENU button on the front panel or the remote to display the Main Menu. Front left, center and right speakers These speakers should be placed at the same relative height from the floor and a similar distance from any walls. Most speakers sound best when located with the tweeter at ear height when you're seated. Typically, the further away from the walls the speakers are, the better they will sound. Ensure that the speakers are aimed at the listener's ears within your chosen seating position. Place these speakers so that their height is approximately 1 meter (3 feet) higher than that of the listener's ears, if feasible. Place these speakers to the sides of, or slightly behind, the primary listening position. Surround left and right speakers The Main Menu appears on-screen: MAIN > INPUT AUTO SETUP SPEAKER SPEAKER SURROUND CHANNEL DELAY SYSTEM MULTI-ROOM 2. Press Setup. MENU CONFIG SIZE X-OVER CONFIG CALIBRATE ADJUST CONFIG CONFIG Surround back left and right speakers These speakers are required for Dolby Digital EX, DTS ES, Dolby Pro Logic IIx, and 7-Channel Stereo. They are also desirable--though not required--for DTS Neo:6. Place these speakers behind the listener so that the angle between each speaker and the listener is approximately 30 degrees. Place these speakers so that their height is 1 meter (3 feet) higher than that of the listener's ears. NOTE ON DIPOLE SURROUND LOUDSPEAKERS: Most dipole surround speakers have an arrow which indicates their proper orientation relative to your video display/screen. Dipoles placed on side walls should have the arrows pointing forward. Dipoles placed on a rear or back wall should have the arrows pointing toward each other to achieve the correct acoustical image in the room. once on the front panel or the remote to select Auto 3. Press SET on the front panel or the remote. The first Auto Setup screen appears on-screen: AUTO SETUP BEFORE STARTING THE SYSTEM PLEASE PLUG THE MIKE IN USING THE FRONT PANEL JACK ** WARNING ** THE TEST TONE IS LOUD PRESS ENTER TO CONTINUE 26 Outlaw Audio Owner's Manual Speaker Configuration Speaker Placement ° Model 990 7. 1 Channel Preamp/Processor 27 Owner's Manual Speaker Configuration 4. Connect the supplied setup microphone to the Setup Mic input jack on the lower right of the front panel. Position the microphone as close as possible to the position your head will usually be in when you are listening. AUTO SETUP > START SETUP :NO Front speaker or microphone is disconnected. After turning power off, check front speaker or microphone connection RETURN TO MAIN MENU You can simply hold the microphone a foot or so in front of your face, or for the most accurate setup, move over one seat and hold the microphone where your head would be if you were sitting in your favorite chair. The setup microphone has a standard 1/4-20 threaded socket on the bottom, so it can be mounted on a photo or video tripod. If you have a tripod handy, you may find it easier to place the mic on the tripod than to hold the mic in place during the setup procedure. Using a tripod will also let you leave the room during setup, so you do not have to listen to the loud test tones. 6. [. . . ] / 12. 7 kg Sequential Delay 50 mA @ 12 VDC 120V, 60Hz only 50W S/N Ratio (ref. 2. 0Vrms A-weighted) 97dB FM Tuner Section Usable Sensitivity (THD 3%, S/N 30dB) 50db Quieting Sensitivity Mono Stereo S/N Ratio (60dBf) Mono Stereo THD (65dBf) Mono Stereo Stereo Separation Capture Ratio IF Rejection Ratio Frequency Response 0. 2% 0. 3% 40dB typ. 3. 0dB 120dB 20 Hz to 15 kHz ± 1. 5dB 72dB 68dB 25. 2dB 43. 2dB AM Tuner Section Usable Sensitivity S/N Selectivity 12. 5mV 51dB 30dB Model 990 7. 1 Channel Preamp/Processor 49 Outlaw Audio Limited Warranty This warranty protects the owner of the Outlaw Model 990 Preamp/ Processor (the PRODUCT) for five (5) years from the date of purchase. This warranty covers all defects in material and workmanship with the following specific exceptions. [. . . ]